background image

Do not burn the battery

Do

 

not

 

expose

 

to

 

rain

 

or

 

water

Hold the chain saw by two hands

Danger of Kickback: never cut with the tip of the chainsaw

This

 

product

 

has

 

been

 

marked

 

with

 

a

 

symbol

 

relating

 

to

 

removing

 

electric

 

and

 

electronic

 

waste.

 

This

 

means

 

that

 

this

 

product

 

shall

 

not

 

be

 

discarded

 

with

 

household

 

waste

 

but

 

that

 

it

 

shall

 

be

 

returned

 

to

 

a

 

collection

 

system

 

which

 

conforms

 

to

 

the

 

European

 

Directive

 

2002/96/CE.

 

It

 

will

 

then

 

be

 

recycled

 

or

 

dismantled

 

in

 

order

 

to

 

reduce

 

the

 

impact

 

on

 

the

 

environment.

 

Electric

 

and

 

electronic

 

equipment

 

can

 

be

 

hazardous

 

for

 

the

 

environment

 

and

 

for

 

human

 

health

 

since

 

they

 

contain

 

hazardous

 

substances.

Do not dispose of batteries. Return exhausted batteries to your local collection or recycling point.

Safety Information (Continued)

To reduce the risk of injury, user must read instruction manual

Warning

Wear

 

dust

 

mask

Wear

 

ear

 

protection

Do

 

not

 

expose

 

to

 

moisture

Wear

 

eye

 

protection

Symbols On The Machine

 12

Summary of Contents for HYC40Li

































Reviews: