background image

2.2.21.

 

Use only genuine replacement parts. 

2.2.21.1.

 

Replacement parts 

that are 

not original may void your warranty and 

can lead

 to malfunction and resulting injuries. Genuine parts are available 

from

 your dealer. 

 

2.2.22.

 

DO NOT modify the compressor. 

2.2.22.1.

 

DO NOT modify the compressor. Always contact the authorized 

service centre 

for 

any repairs. Unauthorized modification may not only 

impair the compressor performance but may also result in accident or 
injury to repair personnel who DO NOT have the required knowledge and 
technical expertise to perform the repair operations correctly. 

2.2.23.

 

Turn off the pressure switch when the compressor is not used. 

2.2.23.1.

 

When the compressor is not used, turn the knob of the pressure 

switch off, disconnect it from the power source and open the drain cock to 
discharge the compressed air from the air tank. 

2.2.24.

 

NEVER touch hot surface. 

2.2.24.1.

 

To reduce the risk of burns, DO NOT touch tubes, heads, cylinder and 

motors. 

2.2.25.

 

DO NOT 

direct the 

air stream 

toward any part to anyones face or body parts.

 

2.2.25.1.

 

Risk of injury, DO NOT direct air stream at persons or animals. 

2.2.26.

 

Drain tank. 

2.2.26.1.

 

Drain tank daily or after 4 hours of use. 

2.2.26.2.

 

Open drain fitting and tilt compressor to empty accumulated water. 

2.2.27.

 

DO NOT stop compressor by pulling out the plug. 

2.2.27.1.

 

Use the “auto/off” knob of pressure switch. 

2.2.27.2.

 

Use only recommended air handling parts acceptable for pressure not 

less than 125 psi (8.6 bar) 

2.2.27.3.

 

Risk of bursting. Use only recommended air handling parts acceptable 

for pressures not less than 125 psi (8.6 bar). 

2.2.28.

 

Replacement parts. 

2.2.28.1.

 

When servicing use only genuine Hyundai replacement parts, all 

repairs should be conducted only by authorized service centre. 

2.2.29.

 

Earthing/Grounding instructions. 

2.2.29.1.

 

This compressor should be earthed/grounded while in use to protect 

the operator from electric shock. The compressor is equipped with a three 
core cable and three-prong grounding type plug to fit the proper 
grounding type receptacle. 

2.2.29.2.

 

The green (or green and yellow) conductor in the cable is the 

earthing/grounding wire. NEVER connect the green (or green and yellow) 
wire to a live terminal. 

2.2.30.

 

Extension cable. 

2.2.30.1.

 

Use only three core cables that have three-prong grounding type 

plugs and three-pole receptacles that accept the compressor’s plug. 
Replace or repair damaged cable. Make sure your extension cable is in 
good condition. When using an extension cable, be sure to use one heavy 

Page 8

Original

Summary of Contents for HY3200S





















Reviews: