manualshive.com logo in svg

Hyundai HSH-121NBE, Service Manual

Share
Download
Hyundai HSH-121NBE Service Manual Download Page 185

 

①

  The condition and process of dehumidifying 

If T

amb

>T

set

+2

℃

, DRY mode will act. The compressor and the outdoor fan will run, and indoor 

fan will run at low speed.   

If T

set

-2

℃

≤

T

amb

≤

T

set

+2

℃

, DRY mode will act. The indoor fan will run at low speed. The 

compressor and outdoor fan stop six minutes after it is started, and restart four minutes later. 

Process of dehumidifying runs circularly as above. 

If T

amb

<T

set

-2

℃

, the compressor and the outdoor fan will stop running, and the indoor fan will run 

at low speed. 

¾

 

In this mode, the four-way valve will not be powered on and the temperature setting range is 

16 ~30

℃

. Monitor displays running symbol, dehumidifying symbol and set temperature.   

 

②

 Protection function 

◆

 Antifreezing protection 

In cooling by dehumidifying mode, when the antifreezing protection is detected, the compressor 

and the outdoor fan will stop running, and the indoor fan will keep running at low speed. When 

antifreezing protection is eliminated and the compressor has stopped for 3 minutes, the whole unit 

will resume running in the original mode. Six minutes’ starting and four minutes’ stop shall be 

met. When the antifreezing protection is detected, the compressor and the outdoor fan will stop 

running, and the indoor fan will keep running at low speed. When antifreezing protection is 

eliminated and the compressor has stopped for 4 minutes, the whole unit will resume running in 

the original mode. 

③

 Other protection  

Other protection is same with that in COOL mode.   

(3) Heat mode ( single cooler wihout this mode) 

①

The condition and process of heating 

If T

amb

≤

T

set

+2

℃

, Heat mode will act. The four-way valve, compressor and outdoor fan will run 

at the same time. The indoor fan will delay two minutes to run at the latest.   

If T

amb

≥

T

set

+4

℃

, the compressor, outdoor fan and four-way valve will be powered on 

continuously. The indoor fan will stop after it blows at the set speed for 60 seconds.   

If T

set

+2

℃＜

T

amb

＜

T

set

+4

℃

, the unit will keep running in the current state.   

¾

 

In this mode, the temperature setting range is 16 ~30

℃

. The monitor displays running 

symbol, heating symbol and set temperature.   

Cooling runs 

Dehumidifying runs 

Stop running   

Run  

Stop 

Low fan speed 

Compressor 

Outdoor fan 

Indoor fan 

T

set

+2

℃

 

T

set

-2

℃

 

T

amb

6 min 

4 min

6 min 

183

Summary of Contents for HSH-121NBE




































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands