manualshive.com logo in svg

Hyundai HiE-S SG Series, Installation Manual, Page: 11 / 13

Share
Download
Hyundai HiE-S SG Series Installation Manual Download Page 11

 

                                                                                                     

www.hyundai-es.co.kr

 

 

 

Page 11 of 13 

 

 

Sales Office 

4th Fl., First Tower, 
55, Bundang-ro, Bundang-gu, 
Seongnam-si, Gyeonggi-do, 
13591 Korea 

Factory 

 

313, Soi-ro, Soi-myeon, Eumseong-gun, 
Chungcheongbuk-do 369-872, Korea 

 

7.  Disposal 

·

 

Users shall dispose of modules according to local disposal regulations. 

·

 

Contact HES for more detailed information related to disposal and recycling. 

 

 

8. 

Disclaimer of Liability 

1)  HES do not have any responsibility and liability for clause as below. 

 

Loss,  damage,  injury  or  expense  resulting  from  improper  installation,  handling  or  use.  The 

installation techniques, handling and use of this product are beyond company control. 

 

Infringement of any third party

’s patent or right that is caused by using HES modules. 

 

Loss, damage, injury or expense resulting from any factor that is unsuspected the  module was 

produced or shipped. 

2)  HES  reserves  the  rights  for  any  change  the  technical  specification  including  the  PV  production,  the 

specifications, or the product information sheets without prior notice. 

 

 

Summary of Contents for HiE-S SG Series














Reviews:

No comments