background image

15

HHC4G User Manual

SECTION 7 - MAINTENANCE

Proper maintenance is important in order to ensure safe, economical, and 
trouble-free operation.    Improper maintenance may cause the air compressor 
to malfunction and can lead to serious injuries or death.

Shut off the compressor before performing any maintenance.  
When the engine is running, make sure the area is 
well ventilated.  The compressed air may contain harmful 
vapours or particles.

Use authorized parts or their equivalent.  The use of replace-
ment parts which are not equivalent quality may damage the 
compressor.

NOTE: Some of these maintenance techniques can be danger-
ous and must be performed by a qualified technician.

In order to maintain high performance and extend the service life of the com-
pressor, periodical inspection and adjustments should be done based on the 
following maintenance schedule:

PROCEDURES

DAILY OR 

BEFORE 

EACH USE

AFTER 

EACH USE

OTHER

General Inspection

X

Drain condensation in 

tank(s)

X

Check for unusual 

noise/vibration

X

Check for air leaks

X

Check safety relief 

valve

X

Inspect air filter, replace 

if necessary

Approx. every 

100 hours

Clean exterior of 

compressor

X

Summary of Contents for HHC2G
























Reviews: