background image

3.

OPERATION

3.1. 

Starting the generator. 

Before starting you MUST disconnect all appliances. All circuit breaker

s

 are to be turned 

OFF. You MUST earth the generator before use. 

3.1.1.  Key start. 

3.1.2. 

Turn the starter key clockwise to the ON positon and allow the control panel to self-test, then turn the 

keyswitch against spring tension to START position until machine starts. DO NOT hold in START position for 

longer that 5 seconds. As soon as the machine starts release the key and allow it to return the ON 

position. If the machine does not start wait 30 seconds before attempting to start again.

 

3.2. 

Control panel start. 

3.2.1.  Turn the starter key to the ON position

 and allow the control panel to self-test

. Then press the Green  

start button, the machine

 will go through a self-start routine.

 

3.3. 

AC application. 

3.3.1.  Allow the machine to warm up for a minimum of five minutes. 

3.3.2.  Connect the appliance to the correct AC socket either 32A outlet or the 63A outlet. Then turn 

on the respective AC breaker. 

3.4. 

Stopping the generator. 

Failure to carry out the following instructions can cause damage to the generator which will not be 

covered under warranty 

3.4.1.  Before stopping the generator YOU MUST firstly turn all appliances OFF, then turn the circuit 

breaker OFF then unplug the appliance from the machine. Move the start key to the OFF position or 
you can press the RED

 

 stop button. Once stopped move the key switch to the OFF position 

3.4.2.  You MUST allow the machine to fully cool down before carrying out any maintenance work. 

Page 11

First issue - 22nd November 2016

Summary of Contents for DHY12500SE

























Reviews: