Ambient daylight threshold [ ]
Press button , the latest surrounding lux value overwrites previous lux value learned, and is set as the daylight threshold. This feature enables the fixture
to function well in any environment.
Detection range [ ]
Press buttons in zone to set detection range at 100% / 50% / 10%.
Hold time [ ]
Press buttons in zone to set hold time at 30s / 1min / 5min / 10min / 30min.
Stand-by period [ ]
3UHVVEXWWRQVLQ]RQHWRVHWWKHVWDQGE\SHULRGDWVVPLQPLQPLQ
1RWH³V´PHDQVRQRIIFRQWURO³
” means bi-leve of dimming control, the light will never switch off.
(i.e. the light remains at the stand-by dimming level until motion is detected.)
Stand-by dimming level [ ]
Press buttons in zone to set the stand-by dimming level at 10% / 20% / 30% .
Daylight sensor [ ]
Press buttons in zone to set daylight sensor at 2lux / 10lux / 50lux.
10
6
Press button ,the sensor goes to manual override or semi-auto function.
15
11
13
12
7
button
10
Power output [ ]
Press button , the output shifts between 80% and 100%, for energy saving purposes.
5
button
5
Dim +/- [ ]
Press button to adjust the light brightness between 10%~100% during hold-time.“+” increases the light level, “-” will decrease the light level.
9
button
9
Lux disable [ ]
Press button , the built-in daylight sensor is disabled, the light will always operate upon detection regardless of ambient light level.
14
button
14
Manual override/ Semi-auto [ ]
Note: The buzzer beeps twice if it is in manual override mode, and beeps once if shifts to semi-auto mode.
button
15
zone
6
zone
11
zone
12
zone
7
zone
13
Scene mode options [ ]
Note: the end-user can fine tune the settings by pressing buttons of detection range / hold time / stand-by period / stand-by dimming level
/daylight sensor , the last setting will over-write that feature of the pre-set scene.
6
11
13
12
7
zone
4
There are 4 scene modes built into the remote control for different applications:
Scene options Detection range Hold time Stand-by period Stand-by dimming leve
Daylight sensor
SC1 100% 1min 10min 10%
2Lux
SC2 100% 5min 10min 10%
2Lux
SC3 100% 10min 30min 10%
10Lux
SC4 100% 10min + 10%
50Lux
8
SECTION 4 SPECIFICATION
Mains voltage
Mains current
Power factor
Operation temperature
Dimming interface
Abnormal protection
Dimming range
Stand-by power consumption
Over-heat protection
EMC standard
Safety standard
DALI standard
Dielectric strength
IP grade
220~240VAC 50/60Hz
Output voltage ( U-out max.)
60V
Ta: -20~+50
℃
Tc:+80
℃
Output short-circuit protection with auto-reset
1~30% PWM dimming; 30~100% analogue dimming.
<0.5W
Over-heat protection with auto-reset
EN55015, EN61547, EN61000-3-2/3
EN61347-1, EN61347-2-13, EN60598-1
IEC62386-102,207
Input
ĺ
output : 3750VAC
IP20
0.3 ~ 0.25A
25W / 500mA / 12 ~ 50V
28W / 550mA / 12 ~ 50V
30W / 600mA / 12 ~ 50V
33W / 650mA / 12 ~ 50V
35W / 700mA / 12 ~ 50V
38W / 750mA / 12 ~ 50V
40W / 800mA / 12 ~ 50V
43W / 850mA / 12 ~ 50V
45W / 900mA / 12 ~ 50V
48W / 950mA / 12 ~ 50V
50W / 1000mA / 12 ~ 50V
53W / 1050mA / 12 ~ 50V
55W / 1100mA / 12 ~ 50V
55W / 1150mA / 12 ~ 48V
55W / 1200mA / 12 ~ 46V
89%
DALI, Switch-Dim., 1-10V
Max. output
power/current/voltage
Max. Efficiency
