HHC9025/I-20180731-A1
HHC9025/I-20180731-A1
Technical Specifications
Functions
1. Lux Off Function
The built-in daylight sensor can measure ambient natural light and switch off
the fixture automatically whenever artificial light is not required (natural light
lux level exceeds daylight threshold).
3. Zero-cross Relay Operation
Designed in the software, the sensor switches on/off the load right at the
zero-cross point, to ensure the in-rush current is minimised, enabling the
maximum life-time of the relay.
Product Type:
Operating Voltage:
HF System:
Transmission Power:
Detection Angle:
Detection Range(DxH):
Time Setting:
Light Control:
Mounting:
Working Temperature:
Rated output current/voltage/power:
Tri-level Control Microwave Motion Sensor
220-240VAC 50Hz/60Hz
5.8GHz CW radar
< 0.2mW
30~150°
Max. 12 x 6m
10s ~ 30 min.
2~50 lux, disable
Indoors, Ceiling & walling mounted
-20 ~ + 60°C
Dimensions (mm)
Installation and Instruction Manual
Integrated SensorDIM LED Driver HEC9025/I
Wiring Diagram
Super-compact sensor antenna, with Hytronik specially designed intelligent
photocell built inside.
Sensor antenna
Model SAM5/I
40.4
2.5 6.6
25.2
35.9
34.7
Cable side entry
24.3
15.5
2.5
25
Ф4
1.5 13
11.2
6.8
8.8
Cable back entry
Ф4.5
Infrared remote receiver
Photocell
104
53
26
4.2
110.7
119.5
LED current
selection
LED -
LED +
N
L
Antenna module
connector
Detection area
Hold-time
Stand-by dimming level
Stand-by period
Daylight threshold
2.Tri-level Control (Corridor Function)
Hytronik builds this function inside the motion sensor to achieve tri-level
control, for some areas which require a light change notice before switch-off.
The sensor offers 3 levels of light: 100%-->dimmed light -->off; and 2
periods of selectable waiting time: motion hold-time and stand-by period;
Selectable daylight threshold and freedom of detection area.
N
L
LED -
LED +
N
L
HEC9025/I
350mA/10-43V/15.7W 500mA/10-42V/21W
550mA/10-40V/22W 700mA/10-36V/25.2W
750mA/10-34V/25.5W 900mA/10-28V/25.2W
1. Press button , the red LED is on for indication.
2. Press button “Sensor off”, the function of movement detection is disabled.
Sensor off [ button ] (Daylight harvest without occupancy)
Settings
1 Detection Range
Sensor sensitivity can be adjusted by selecting
the combination on the DIP switches to fit
precisely for each specific application.
Note: by choosing “Sensor OFF”, it
becomes an ordinary driver without
occupancy detection.
100%
75%
50%
Sensor OFF
1 2
Note: “0s” means on/off control; “+∞
”means the stand-by period is infinite and
the light is effectively controlled by the
daylight sensor, off when natural light is
sufficient and automatically on at dimming
level when insufficient.
2 Hold Time
4 Stand-by period (corridor function)
Select the DIP switch configuration for the light
on-time after presence detection.
This function is disabled when natural light is
sufficient.
This is the time period you would like to keep at
the low light output level before it is completely
switched off in the long absence of people.
3 Daylight Threshold
Set the level according to the fixture and
environment. The light will not turn on if ambient
lux level exceeds the daylight threshold preset.
Please note that the ambient lux level refers to
internal light reaching the sensor.
Disabling the daylight sensor will put the sensor
into occupancy detection only mode.
2
1
50Lux
10Lux
2Lux
Disable
I
II
III
IV
3
2
1
30min
5s
30s
1min
5min
10min
20min
I
II
III
IV
V
VI
VII
0s
10s
1min
5min
10min
30min
1H
∞
+
2 3
1
5 Stand-by dimming level
The setting is used to select the desired
dimmed light level used in periods of absence
for enhanced comfort and safety.
30%
20%
10%
50%
2
1
I
II
III
IV
Description of the Button Functions
(remote control HRC-11)
HRC-11
7
9
11
12
13
14
15
2
4
1
3
6
8
10
5
& A
4h
h
4 h
RESET [ button ]
Press button , all settings go back to the DIP switch settings.
2
2
Shift [ button ]
Press button , the LED on the top left corner flashes to indicate mode selection.
All values / settings in RED are in valid for 20 seconds.
3
3
Auto Mode [ button ]
Press button to initiate automatic mode. The sensor starts working and all
settings remain as before the light was switched ON/OFF.
Note: The function of “SEMI-AUTO” is disabled.
4
4
5
3
Permanent ON/OFF [ ]
Press button to select permanent ON or permanent OFF mode.
* Press button / to resume automatic operation.
button
1
1
2
4
Power output [ button ]
Press button , the light output shifts between 80% and 100%.
6
6
Twilight [ button
⑤
]
1. Press button "Shift", the red LED is on for indication.
2. Press button "Twilight", the function of movement detection is disabled.
This unit is now a LED driver plus daylight sensor with daylight harvest
function.
