background image

SAFETY PRECAUTIONS

MAINTENANCE AND REPAIR

• The Service Manuals are updated on a regular basis, but may not reflect recent design changes to the

product. Updated technical service information may be available from your local authorized Hyster

®

dealer. Service Manuals provide general guidelines for maintenance and service and are intended for

use  by  trained  and  experienced  technicians.  Failure  to  properly  maintain  equipment  or  to  follow

instructions contained in the Service Manual could result in damage to the products, personal injury,

property damage or death.

• When  lifting  parts  or  assemblies,  make  sure  all  slings,  chains,  or  cables  are  correctly  fastened,  and

that  the  load  being  lifted  is  balanced.  Make  sure  the  crane,  cables,  and  chains  have  the  capacity  to

support the weight of the load.

• Do not lift heavy parts by hand, use a lifting mechanism.
• Wear safety glasses.
• DISCONNECT THE BATTERY CONNECTOR before doing any maintenance or repair on electric lift

trucks. Disconnect the battery ground cable on internal combustion lift trucks.

• Always  use  correct  blocks  to  prevent  the  unit  from  rolling  or  falling.  See  HOW  TO  PUT  THE  LIFT

TRUCK ON BLOCKS in the Operating Manual or the Periodic Maintenance section.

• Keep the unit clean and the working area clean and orderly.
• Use the correct tools for the job.
• Keep the tools clean and in good condition.
• Always  use  HYSTER  APPROVED  parts  when  making  repairs.  Replacement  parts  must  meet  or

exceed the specifications of the original equipment manufacturer.

• Make sure all nuts, bolts, snap rings, and other fastening devices are removed before using force to

remove parts.

• Always fasten a DO NOT OPERATE tag to the controls of the unit when making repairs, or if the unit

needs repairs.

• Be sure to follow the WARNING and CAUTION notes in the instructions.
• Gasoline,  Liquid  Petroleum  Gas  (LPG),  Compressed  Natural  Gas  (CNG),  and  Diesel  fuel  are

flammable.  Be  sure  to  follow  the  necessary  safety  precautions  when  handling  these  fuels  and  when

working on these fuel systems.

• Batteries generate flammable gas when they are being charged. Keep fire and sparks away from the

area. Make sure the area is well ventilated.

NOTE:  

The following symbols and words indicate safety information in this

manual:

  WARNING 

Indicates a hazardous situation which, if not avoided, could result in death

or serious injury.

  CAUTION

Indicates a hazardous situation which, if not avoided, could result in minor

or moderate injury and property damage.
On  the  lift  truck,  the  WARNING  symbol  and  word  are  on  orange  back-

ground. The CAUTION symbol and word are on yellow background.

Summary of Contents for A238






















Reviews: