background image

                                                                                                                  

                                                                                                                                                Page 24

5.5.3 Steam line and condensate

hose installation types

Installation type 1

Steam manifold is positioned more than
500 mm above device upper edge:

»

Run steam hose to a height of 400 
mm/16 inch minimum above the 
steam humidifier and then to the 
steam manifold with a continuos 
incline of 5 to 10 %.

»

Feed condensate hose from steam 
manifold with a decline into waste-
water pipe or drain.

»

As a steam barrier, lay out a 200 
mm/8 inch min. loop (s. schematic 
representation below). Minimum dis-
tance from steam manifold to loop 
must be 500 mm/20 inch. Fill loop 
with water prior to steam humidifier 
commissioning.

Installation type 2

Steam manifold is positioned less than
500 mm above or below device upper
edge:

In this arrangement the condensate hose
cannot be fed back to the steam humidifier.

»

Run steam hose to a height of 400 
mm/16 mm minimum above the 
steam humidifier and then to the 
steam manifold with a continuos 
decline of 5 to 10 %. 

»

Feed condensate hose to a waste-
water pipe/drain with a 200 mm/8 
inch diameter loop as a steam bar-
rier. Minimum distance from steam 
manifold to loop must be 500 mm/20 
inch. Fill loop with water.

Steam cylinder

Steam manifold

Steam
hose

Cond

ensa

te

hose

Installation type 1,

Device

upper edge

schematic representation

500 mm

20 inch

min.

400

 mm

16 inch

200

 mm

/8‘‘ 

min

Rmin

DN25: 200 mm/8 inch

DN40: 400 mm/16 inch

Steam cylinder

Steam

hose

Device

upper

Condensate

hose

Drain

Detail „x“

wrong!

Installation type 2,

schematic representation

edge

Detail „x“

Rmin

DN25: 200 mm/8 inch
DN40: 400 mm/16 inch

400 mm 16

 inch

200 mm  8 i

nch

Please note

Summary of Contents for FlexLine Plus

























































Reviews: