background image

5

PRESSURE INSTALLATION

1 -

 

Power to the hydromassage bathtub must be turned OFF

 and all water must be drained from 

the bathtub before proceeding. 

2 - 

Loosen nuts and remove Heater Ready fitting and existing gaskets (see Fig. 8).

3 - 

Remove the new heater gaskets included with your Pure Heat heater and install them onto the 

plumbing tailpieces, making sure the gasket ridge is seated in the tailpiece groove (see Fig. 9).

TAILPIECE

GASKET

PLUMBING

4 -

 You are now ready to install the heater in the open space where the Heater Ready fitting was located 

(ensure that the gaskets remain in place). Slide both heater nuts inward toward the center of the 
heater to expose the mating surfaces of the heater housing. Slide the heater carefully into place 
between the tailpieces and gaskets and hand-tighten heater nuts. If you use a wrench be careful not 
to over-tighten, the nuts can crack (see Fig. 10). 

       

Fig. 9

Fig. 10

Fig.8

HEATER READY

ASSURE YOU ARE INSTALLING 
A PRESSURE MODEL FOR THIS 
LOCATION

IF THERE IS INSUFFICIENT 
SPACE, THE HEATER MAY BE 
ROTATED TO THE CONTROL 
BOX DOWN POSITION.

CONTINUE ON TO PAGE 12
“BONDING YOUR HEATER”

-UP SERIES

PRESSURE

Heater Ready Fitting Installed

www.bathheaters.com

Summary of Contents for Pure Heat PH101-10UP





















Reviews: