background image

14

THERE ARE NO SERVICEABLE PARTS INSIDE HEATER - DO NOT OPEN

NOTHING WORKS!

Main Breaker is OFF - Set to On
GFCI Tripped - Press Reset
Power Cord not plugged in - Plug in power cord (if plugged in, is plug lit?)

HEATER “ON” LIGHT DOES NOT TURN ON

Overheat Protection Tripped - Power off, let cool, then power on
Power cord not plugged in - Plug in power cord (if plugged in, is plug lit?)
GFCI Tripped - Press Reset
No Power to Heater - Reset breaker at service panel
Pump Is Not Running - Activate hydromassage pump
Water Temperature Too High 

HEATER “ON” LIGHT WILL NOT TURN OFF

Water Level Too Deep for Pressure Switch Setting - Lower Water Level
Pressure Switch Defective - Replace Heater
Heater Wiring Error - Replace Heater

OVERHEAT PROTECTION TRIPPED

 

Water Blockage - Correct/Remove Blockage
Low Water Flow - Correct Problem
High-Limit Will Not Reset - Replace Heater

WATER LEAKS FROM CONTROL BOX

Defective Component - Replace Heater 

GFCI TRIPS OCCASIONALLY

Lightning or Electrical Storm, Power Surge, Extremely Humid Conditions or Radio Frequency 
Interference - Reset GFCI Note: Assure Heater is Properly Grounded and Bonded
Inspect Heater for Leaks or Moisture - Correct or Replace as Required

GFCI TRIPS REPEATEDLY

Defective Component - Replace Heater

CIRCUIT BREAKER TRIPS

Breaker Size Improper - Contact a qualified service technician 
Heater Requires a DEDICATED Circuit - Assure No Other Appliances are on this Circuit 

TEMPERATURE NOT REACHING COMFORT ZONE

Designed to maintain bath water temperature and is not meant to heat water from cool or cold.

TROUBLESHOOTING

Summary of Contents for Pure Heat PH101-10UP





















Reviews: