background image

 4

www.hydrofarm.com

2. 

 Screw the water pipe connector off the 

water tank outlet. Set the connector aside.

3. 

 The outlet at the side of the water tank is 

sealed by default for drainage. If you decide 

to install a pipe for continuous drainage, 

use a power tool to drill the side outlet so 

you to have an opening of sufficient size to 

allow water to drain through smoothly.

4. 

 Screw the connector back to the outlet 

tightly. A washer is pre-installed into the 

connector to prevent leakage. 

Water 

tank

Outlet at 

the side of 

water tank

Water pipe 

connector

 

5. 

 Install the included drain pipe to the water 

pipe connector on the tank, through the 

opening on the machine housing. Direct the 

pipe to the desired area before operating 

the machine.

6. 

 If needed to replace or extend the drainage 

pipe, use IDФ11mm (7/16in) piping.

7. 

 Shut the front panel.

 

Opening 

for drain 

pipe

Continuous 

drain pipe

 

WARNING: 

Do not block the drainage pipe. The 

end of the drainage pipe should not be higher 

than the water tank outlet. If the drainage pipe 

end is higher than the outlet, water will not 

drain properly and could damage components 

DRAINAGE INSTALLATION

DRAINAGE WITH THE BUILT-IN 

WATER TANK

 The unit is designed to use the built-in water 

tank for drainage by default. When the tank 

is full, the screen will display “

FULL

” and also 

make a buzzing sound.

1. 

Press the 

POWER

 button to turn off the 

machine. 

2. 

 To empty the water tank, open the front 

panel to access the water tank. 

3. 

 Grab the handle of the water tank and pull 

it out horizontally. 

4. 

After disposing of the water, insert the tank 

back into place until you feel the internal 

clamp fully clamps onto the nozzle of the 

tank. Close the front panel. 

5. 

 Press  the 

POWER

 button to resume 

operation.

CONTINUOUS DRAINAGE WITH 

THE DRAINAGE PIPE

In extremely wet conditions, the water tank 

may be filled up frequently. You may consider 

setting up continuous drainage by using the 

drainage pipe for convenience. 

1. 

 Open the front cover of the machine, 

remove the tank, and empty the water 

from the tank. 

INSTRUCTION MANUAL

Summary of Contents for AADHC100P









Reviews: