manualshive.com logo in svg

HydroBikes EXPLORER I, Assembly, Operation And Safety Instructions

Share
Download
HydroBikes EXPLORER I Assembly, Operation And Safety Instructions Download Page 22

22 | www.HydroBikes.com

EXPLORER

®

 I AND EXPLORER

®

 II SPECIFICATIONS

DIAGRAM/DRAWING OF EXPLORER I & 2

EXPLORER

®

 I

Width (Hull-Hull): ............... 42 in.
Width (Outside): ................ 55 in.
Weight: .......................... 95 lbs.

1

Capacity: ......................400 lbs.

2

EXPLORER

®

 II

Width (Hull-Hull): ............... 84 in.
Width (Outside): ................ 97 in.
Weight: ........................170 lbs.

1

Capacity: ..................... 600 lbs.

2

Common Features/Specifications

Length: .......................................................................................10 ft. 
Height: .....................................................................................53 in. 
Gear Ratio: ............................................................................... 8.6.1 
Propeller Diameter:.....................................................................12 in. 
Prop Draft – 200 lb. rider: ..........................................................18 in. 
Hulls: ............................................................ Roto-Molded Polyethylene 
Hull Draft – 200 lb rider: ..............................................................9 in. 
Frame – 19 inches: ........................................ Powder-Coated Aluminum 
Adjustments: .................................................Quick Release Seat Clamp

1

 Weight may vary with accessories 

2

 Includes rider and cargo

MAINTENANCE INFORMATION

For maintenance information please refer to our Maintenance Manual 
or visit 

www.HydroBikes.com

.

Summary of Contents for EXPLORER I

























Reviews:

No comments

Brands by name

Popular brands

Load more brands