background image

THANK  YOU

:    The  employees  and  management  of 

HYDRO TEK SYSTEMS, INC. thank you for selecting 
our  products.    The  production  and  quality  assurance 
team have taken the greatest care to ensure that your 
new  pressure  washer  exceeds  the  standards  set  by 
you, the customer, and by Hydro Tek engineering and 
ISO9001:2008 quality management standard. 

YOUR  RESPONSIBILITY:   

This  operator’s  manual 

was  compiled  for  your  benefit.    By  studying  and 
following 

the 

safety, 

installation, 

operation, 

maintenance, 

and 

troubleshooting 

information 

contained within,  you can look forward to many years 
of  trouble-free  service  from  your  equipment.    Every 
person who will operate the equipment must read and 
follow  the  safety  warning  and  operating  instruction 
sections of this owner’s manual prior to use.  You are 
responsible  for  operating  the  product  properly  and 
safely.    You  are  also  responsible  to  follow  the 
maintenance  schedule  on  the  back  page  of  this 
manual to keep your warranty active. 

FREIGHT  DAMAGE:   

If  delivered  by  a  trucking 

company,  please  inspect  for  any  concealed  freight 
damage  and  note  this  on  the  paperwork  from  the 
trucking  company  before  signing.    Should  you  find 
damage  has  occurred  during  shipping,  do  not  return 
the  damaged merchandise  to  manufacturer  or  dealer, 
but  file  a  claim  immediately  with  the  freight  carrier 
involved. 

QUESTIONS:   

Help  us  provide  you  with  the  fastest 

service.    Please  locate  the  enclosed  warranty 
registration card and return it to Hydro Tek to register 
your machine.   
If problems occur, contact the dealer you bought your 
machine  from,  a  local  authorized  Hydro  Tek  service 
center, or call manufa1 (909) 799-9222 option 
4 or ask for technical services.   

 

GETTING STARTED:  

If your dealer has not prepared 

the machine for startup, you may need to connect the 
hose to the pressure outlet on the washer and connect 
the  other  end  of  the  hose  that  swivels  to  the  trigger 
gun inlet  and tighten.  Mobile Wash Skids are engine 
powered  and  shipped  from  the  manufacturer  with  the 
fuel tanks empty and without the battery.  Connect the 
battery  cables  (positive  lead  first)  and  follow  the 
operation  instructions  for  starting.    High  Pressure 
Steamers  are  electric  powered  and  will  require  an 
appropriate  electric  outlet  or  disconnect  box  and  an 
electric  plug  that  is  rated  for  your  machine’s  voltage 
and  amperage  and  matches  to  your  electrical  socket.  
Smaller  machines  are  equipped  with  a  ground  fault 
interrupter  on  the  electrical  cord  and  you  will  need  to 
press  the  reset  button  after  it  is  plugged  in.    (See 
Operating  Instruction  section  and  enclosed  page  on 
Installation Guidelines). 

 

 

ONE  YEAR  PARTS  WARRANTY: 

Hydro  Tek 

Systems,  Inc  will  provide  replacement  parts  for 
Hot2Go® branded pressure washers and accessories, 
including Hydro Vacuum and Hot Link heaters, for one 
year from the date of original retail purchase.  You will 
pay  transportation/shipping  costs  and  travel  time.  
(Labor is not included) 
 

Items and Conditions Not Covered: 

1.  Normal wear items such as discharge hose, guns, 
wands,  spray  arms,  nozzles,  quick  couplers,  o-rings, 
motor & generator brushes, filters, fuses, belts, & tires. 
2.  Cost of regular maintenance/adjustments, damage 
from lack of maintenance or correct operation 
3.  Damage due to freezing, abrasive fluids, chemical 
deterioration, scale build-up, or water ingress. 
4.  Damage  from  fluctuation  in  electrical  or  water 
supply. 
5.  Any  product  or  part  that  has  been  altered, 
modified,  over  pressurized,  misused,  or  has  been  in 
an accident. 
6.  Dealer  installation  or  damage  from  improper 
installation of the machine or alteration by a dealer or 
promise  of  additional  warranty  from  dealer.    The 
manufacturer  warranty  is  not  transferable  from  the 
dealer  to  the  retail  purchaser  on  used  or  rented 
equipment. 

 

WARRANTY PROVIDED BY OTHERS:  Gasoline and 
diesel  engines  and  some  electric  motors  are 
warranted by the manufacturer of the component and 
their  warranty  is  provided  through  the  manufacturer’s 
service centers. Contact your authorized distributor for 
the  closest  repair  center.    Additional  extended 
warranties  from  3  to  5  years  may  be  provided  by 
engine or pump manufacturer. 
 

GENERAL 

CONDITIONS

 

Manufacturer’s 

responsibility  with  respect  to  claims  is  limited  to 
making  the  required  repairs  or  replacements  to  the 
original retail user, and no claim of breach of warranty 
shall be cause for any cancellation or rescission of the 
contract 

of 

sale 

of 

any 

Hot2Go® 

product.  

Manufacturer reserves the right to change or  improve 
the design of any of its products or illustrations without 
assuming  any  obligation  to  modify  any  product 
previously manufactured. 
This  supersedes  any  and  all  previous  warranty 
statements  for  products  purchased  after  April  2014.  
Manufacturer  is  not  liable  for  indirect,  incidental  or 
consequential  damages  including  any  cost  of 
substitute  equipment,  loss  of  revenue,  pecuniary 
expense  or  loss,  or  inability  to  use  a  Hot2Go® 
product. 

 

Manufacturer 

disclaims 

all 

implied 

warranties,  including  those  of  merchantability  and 
fitness  for  use  for  a  particular  purpose.    Some  states 

INTRODUCTION 

– WARRANTY 

 

 

 

 

 

Summary of Contents for Hot-2-Go Series





















Reviews: