background image

FIXTURES

No 

f

ixtures can be mounted on the tub deck. Floor and wall-mounted fixtu

r

es are required.

Wall-Mounted

The position of the tub and the reach of the spout are critical. Pay special attention to the spout

reach when choosing your fixtu

r

es. Be careful to ensure the spout will extend out far enough to clear the tub deck

and the falling water will not hit too high up the side wall of the tub and splash.

Floor-Mounted

Some freestanding fixtu

r

es must be anchored to the tub drain for stabilization.

6


Remote Mounting Blower: 

Due to the limited space between the inner and outer shell on all of

  t

he Metro

 

C

ollection

 

f

reestanding tubs, the blower must be remote mounted. In addition to the air pipe there is one

 

electrical connection

 

between the tub and the blower. Th

e electrical co

nnection and the air pipe exit through the

 

bottom end of the bath.

 

It is always desirable to remote mount the air blower as close to the tub as possible to

 

minimize loss of heat.

 

Pipe

 

insulation may be used on the air line to minimize heat loss.

.

THERMAL AIR 

LOOP

Blower

Air hose 
(connect to tub)

1 ½” schedule 

40 PVC pipe 

(not supplied)

1 ½”

check valve 

(supplied)

 This is a sub floor drain. Access from below tub is recommended for installation. If there is no access from

 

below, the installation is more difficult. Clearance for the drain will be required and the floor near the overflow will

 

need to be completed after the drain is installed. 

Please s

ee picture below

.

Hydro Systems recommends using clear 100% silicone sealant

DO NOT use plumber’s putty.

INSTALLATION  INSTRUCTIONS

Thermal Air Loop:

 

A loop made of 1 ½” 

schedule 40 PVC

 

must be installed at the 

outlet of the blower

 

(PVC pipe and 90-

degree fittings not supplied) and must be at 
least 2” above

 

rim of tub with 1 ½” check 

valve (supplied) installed in horizontal 
position at the top

 

of the loop. If loop 

cannot be installed at blower location it can 
be installed at an alternate location in line 
prior to tub. If blower is installed at least 2” 
above rim of tub, attic or closet loop is not 
required. Please see illustration to the right.

Summary of Contents for Ston Series









Reviews: