Contents
1. Mechanism...................................................................................................................................... 1
1.1 Notes for Your Safety
........................................................................................................... 1
1.2 Description
............................................................................................................................ 1
1.3 Identification
.......................................................................................................................... 1
1.4 Transport and Unpacking
..................................................................................................... 2
1.5 Accessories Supplied
........................................................................................................... 2
1.6 Preparations for installing the barfeeder
............................................................................ 2
1.7 Mounting, Anchoring and Alignment
.................................................................................. 3
1.8 Changing the Pushrod Position
........................................................................................... 4
1.9 Retraction of the Barfeeder for Spindle Service
................................................................. 4
1.10 Material Rack Height and Diameter Adjustment
............................................................... 4
1.11 Maintenance
........................................................................................................................ 4
Figure 1 – Floor Plan
........................................................................................................... 5
Figure 2 – Assembly Plan
.................................................................................................... 6
Figure 3 – Manual Adjustments
.......................................................................................... 7
Figure 4 – Changing Pushrod Piston
................................................................................. 8
Figure 5 - Retracting The Barfeeder
.................................................................................. 9
Figure 6 - Transportation by forklift truck
........................................................................ 10
Figure 7 - Transportation by crane/hoist cables
............................................................. 11
Figure 8 – Greasing the Ball screw
.................................................................................. 12
2. Operation Panel............................................................................................................................ 13
2.1 Power On and First Screen
................................................................................................ 13
2.2 Select Manual / Auto mode
................................................................................................. 14
2.3 Manual operation
................................................................................................................ 15
2.4 Auto cycle
............................................................................................................................ 16
3. User Setup .................................................................................................................................... 22
3.1 User Setup
Introduction
..................................................................................................... 22
3.2 BAR TYPE / Diameter
.......................................................................................................... 24
3.2.1 Bar Type
..................................................................................................................... 24
3.2.2 Bar diameter Setting
................................................................................................. 25
3.2.3 Material Selection
..................................................................................................... 25
3.2.4 Push torque Adjustment
.......................................................................................... 26
3.3 Component Length
............................................................................................................. 27
3.4 Position Setup
..................................................................................................................... 28
3.4.1 End of Bar Position
.................................................................................................. 28
3.4.1.1 Spindle length Setup
...................................................................................... 29
3.4.1.2 Clamping length Setup
................................................................................... 29
3.4.2 Loading selection
..................................................................................................... 30
3.4.3 Pushrod retract Position
......................................................................................... 32
3.5 Feeding type
........................................................................................................................ 34
3.5.1 Sub spindle Pull
................................................................................................. 35
3.5.2 Barfeeding with / without Turret
...................................................................... 38
3.6 Back Stop
............................................................................................................................ 50
3.7. Shaft Load
........................................................................................................................... 54
3.8 Chucking mode
................................................................................................................... 56
3.9 Center line correction
......................................................................................................... 57
3.10 Barfeed Programs
............................................................................................................. 58
3.10.1 Ways To search DATA Address
............................................................................ 58
3.10.2. To Save MMI Data to DATA 01
.............................................................................. 60
3.10.3. To Transfer DATA 10 to MMI Data Base
............................................................... 64
3.10.4. To Reset DATA 10
.................................................................................................. 66
3.11 Other
.................................................................................................................................. 68
3.11.2
Eject remnant
....................................................................................................... 68
Summary of Contents for MSV 80
