background image

5

04/05

ID#   21179004

To ensure optimal playability of backboard system, a

close tolerance fit between the elevator components

and hardware is required. Test-fit large bolts into large

holes of elevator tubes, backboard brackets, and

triangle plates. Carefully rock them in a circular motion

to ream out any excess paint from holes if necessary.

PARTS LIST 

(SEE HARDWARE IDENTIFIER)

BEFORE YOU START!

Item Qty

Part No.

Description

1

1

908164

Top Pole Section

2

1

908114

Middle Pole Section (with Label)

3

1

908165

Bottom Pole Section

4

2

900223

Wheel Bracket

5

2

206940

Axle, 21" Long

6

2

226403

Wheel 6”

7

4

206938

Pushnut, Black

8

1

200117

Base

9

1

203223

Carriage Bolt, 5/16-18 x 1" Long

10

1

202662

Hex Bolt, 5/16-18 x 4.5" Long

11

9

203218

Washer 5/16

12

1

200188

Rod 3/8 x 5.25" Long

13

1

202822

EyeBolt, 3/8 -16 x 3.75" Long

14

2

906410

Tank Strut

15

1

200516

Bolt Cover

16

1

200123

Upper Pivot Bracket

17

1

206948

Lower Pivot Bracket

18

2

900122

Hinge Tubes

19

1

200512

Hex Bolt, 3/8-16  x 3.5" Long

20

6

203232

Flat Washer 3/8-3/4

21

1

206252

Hex Bolt, 3/8-16 x 1" Long

22

15*

203100

Flange Nut 5/16-18

23

1

203330

Hex Bolt, 3/8-16  x 4.5" Long

24

2

203527

Spacer, Plastic, .75" O.D., 1.53" Long

25

2

203528

Spacer, Plastic, 1.25" O.D., 1.53" Long

26

4

203103

Carriage Bolt, 5/16-18 x 2" Long

27

1

203540

Height Indicator Window

28

3

201129

Spacer, Metal, .50" O.D., 1.8" Long

29

1

803531

Strut Assembly

30

1

803553

Handle Assembly

31

1

203593

Shoulder Bolt, 5/16-18 x 1.25" Long

32

2

203688

Spacer, Plastic, .75" O.D., 2.25" Long

33

2

900867

Triangle Plates

Item Qty

Part No.

Description

34

1

207103

Pole Cap

35

4

908119

Elevator Tube

36

1

808115

Pole Bracket

37

9

206340

Nut, Nylock, 1/2 -13

38

2

203053

Bolt, Carriage, 5/16-18 x 4" Long

39

4

202862

Spacer, Plastic, .50 O.D., 1.19" Long

40

8

204847

Bolt 1/2-13  x 9.5" Long

41

1

201139

Bolt 1/2-13  x 4.5" Long

42

4

201682

Spacer, Plastic, .50 O.D., 1.88" Long

43

2

203798

Bolt 5/16-18 x 1.5" Long

44

2

202273

Spacer, Metal, .50 O.D., 5-7/8" Long

45

1

203099

Nut, Nylock, 5/16-18

46

2

206360

Bolt 3/8-16  x 2.625

47

5*

203063

Nut 3/8-16  Nylock

48

2

900846

Board Brackets

49

1

200119

Front Cover

50

4

265601

Bolts, Carriage, 5/16-18 x 3.5" Long

51

1

206219

Base Plug

52

1

203124

Tie Down Stake

53

1

201568

Anchor Strap

54

1

203532

Label Height Adjustment

55

2

240027

Nut, Nylock 1/4-20

56

1

203535

Strip, Height Indicator

57

1

203536

Height Label

58

1

203537

Hook, Height Indicator

59

1

240019

Bolt 1/4-20 x .75" Long

60

2

202274

Spacer, Metal, .50 O.D., 3-1/2" Long

61

1

206956

Plastic Disc, Black, 5" O.D.

62

2

226401

Wheel 4”

63

2

203160

Weld Stud, 5/16-18 x 1.5" Long

64

1

240017

Bolt, Hex Head, 1/4-20 x 2-1/4" Long

65

1

203274

Foam Pad, 3/32 Thick, 5" x 5"

* You may have extra parts with this model.

Summary of Contents for Portable Basketball System






























Reviews: