Hybrid KWADRA FL LED Installation And Maintenance Manual Download Page 5

Self-contained emergency lighting luminaire

5/8

IMM - KWADRA FL LED - AT_CT - PL_EN V01

IP65/IP20

EN

KWADRA FL LED

INSTALLATION AND MAINTENANCE MANUAL

MOUNTING TYPE

Mounting in a suspended ceiling

OPERATING MODE

NM

– NON-MAINTAINED – 

luminaire  operates  in  emergency 

mode after power supply failure

SM

SWITCHED MAINTAINED 

–  luminaire  operates  in  emer

-

gency mode after power supply failure, mains operation 

controlled by the switched phase L’

N

NIGHT – luminaire operates in emergency mode after po

-

wer supply failure, mains operation controlled from the 

CT central unit

SYSTEM VARIANT

AT

– AUTOTEST – 

internal  components,  battery  and  light 

source tests being performed automatically

CT

CENTRALTEST – 

internal components, battery and light 

source  tests  being  performed  on  command  from  the 

main unit of central management system

TESTS

The microcontroller-based control and test unit performs automatically (AT) or on order from the central management system (CT) two types of tests: 

TEST A

internal components and light source test lasting 60 seconds – performed every 30 days for the AT system variant 

TEST B

internal components, light source and operation duration test (till the battery is fully discharged) – performed every 360 days for the AT system variant

The first TEST A will be performed 10-30 days after the power-up, and TEST B 30-90 days, after the power-up (AC, battery). 

OPTICS

AREA

(AR) symmetrical light distribution in all directions, rec

-

ommended  for  use  in  places  of  considerable  height 

or to illuminate fire points

AREA / AREA PLUS

ROAD

ROAD PLUS

SIDE

ROAD

(RO) light distribution mainly along the escape route, rec

-

ommended for use in high corridors

ROAD 

PLUS

(RP)  light  distribution  mainly  along  the  escape  route 

with a much greater range than for the ROAD optics, for 

small heights

SIDE

(SD)  light  distribution  directed  to  one  side,  for  wall 

mounting, spot illuminating

TECHNICAL DATA

Supply voltage

230V AC 50/

60HZ

Current consumption (3W)

NM

4,5W

SM, N

10W

Protection class

I

Ingress protection

IP65/IP20 

1) 

Light source type

LED module 

2)

Light source temperature

5700K

Light source supply power

1W, 2W, 3W

Light source lifespan

> 50 000h

Battery type / voltage

Ni-MH

4,8V

Battery capacity

1,6; 2,1; 4,0Ah

Battery recharging time

< 24h

Emergency operation time (taw)

1h, 2h, 3h

Ambient temperature range

+5 – +35˚C

TE: 

3)

  -25 – +40˚C

Supply cable cross-section area

NM

3 x 0,5-2,5mm

2

SM, N

4 x 0,5-2,5mm

2

Supply cable diameter

≤ 13mm

Communication cable diameter

CT

≤ 7mm

Suitable for through wiring

YES

Suitable for surface wiring

NO

1)

 Luminaire in internal/external zone, IP20 for luminaires without seal;  

2)

 Non-exchangeable but serviceable light source; 

3)

 TE – extended temperature range

Summary of Contents for KWADRA FL LED









Reviews: