manualshive.com logo in svg

HWH 625S Series, Service Manual

Share
Download
HWH 625S Series Service Manual Download Page 8

MI91.1205

26OCT07

625 TROUBLE SHOOTING STEPS

MANUAL OPERATION

MP85.2930

PART 2.  Continued. . .

b.   LED’s 36 and 37 are on, LED 39 is off.  Check for +12 volts between PIN 4 

(ground-white wire) and PIN 5 (+12-red wire) at the touch panel.

c.   LED 37 is on.  LED 36 is off.  LED 39 may or may not be on, blinking.

If there is no voltage between PIN 4 and PIN 5 at the touch panel, check for 

Check voltage

Less than 11.3 volts at the touch panel may indicate that there is a low voltage 

situation for the leveling system but the system may still functions.  If there is less 
than 11 volts at the touch panel, the voltage  problem should be taken care of before 
proceeding.  If there is a voltage problem, check  the voltage between PIN 4 (gnd) 
and PIN 6 (ign) of CN8 at the control box and PIN 4 (gnd)  and PIN 3 (ign out) of CN8.  

If  there is more than 1(one) volt difference, replace the control box.  If voltage 

between PIN 4 and PIN 6 is low, the problem is the ground from the white wire in the 
4 pin gray connector or the voltage on the red 6120 wire in the CN8 connector for PIN 6.

voltage between pins 3 (ign out) and 4 (gnd) of CN8 at the control box.  If there is 
good voltage, the problem is the touch panel cable or it’s connections.  If there is no 
voltage between pins 3 and 4, check for voltage on the legs of poly fuse PF3.  If there 

is no voltage on either leg, replace the control box.  If there is voltage on one leg of 

the poly fuse, unplug  the touch panel cable at the touch panel and recheck pins 3 
and 4.  (It will take about 30  seconds for the poly fuse to reset).  If voltage is now 

present, replace the touch panel. If there is still no voltage, remove the 6800 wire from 

the CN8 connector and recheck pins 3 and 4.  If there is voltage now, the 6800 wire is 
shorted to ground. If voltage is still not present, replace the control box.

between PIN 4 (gnd) and PIN 6 (ign) of CN8 at the control box.  If there is less than 12 

volts present, check the ground and ignition supply connections for any problems including 

corrosion.  If there is good voltage between pins 4 and 6, replace the control box.

If the LED is not on, the 7699 wire going to the master warning light and buzzer 

SEE: MP85.091C or MP85.304R or MP85.056J

a.   Check red LED 32.  If the LED is on, replace the control box.  

is shorted to ground.

4.   The "TRAVEL MODE" light is on AND the master "JACKS DOWN" warning light and buzzer are on.

SEE: MP85.185J

SEE: MP85.2930 & MP85.185J

RETRACT

EXTEND

HWH  COMPUTERIZED LEVELING

SECURELY BEFORE REMOVING TIRES OR CRAWLING UNDER VEHICLE.

UNDERSTAND OPERATOR’S MANUAL BEFORE USING. BLOCK FRAME AND TIRES

TOUCH PANEL CONNECTIONS

625 SERIES LEVELING SYSTEM

ELECTRICAL CONNECTION DIAGRAM

6 PIN UML CONNECTOR

5 PIN MTA CONNECTOR

WHITE

COLOR

WIRE

GREEN

YELLOW

LINK LIGHT

3

2

5

3
4

6

5

4

1

RED

PIN #

2

1

NO CONNECTION
ACCESSORY

NO CONNECTION
LEVEL

STORE
LED

6230
6800

NUMBER

WIRE 

MANUAL

STOP

EMERGENCY

PIN 1

STORE

AUTO

AUTO
LEVEL

MODE

CAUTION!

SLOPE

NOT IN
PARK/

TRAVEL

BRAKE

DUMP

EXCESS

R

SW GND FROM TOUCH PANEL FOR LEVEL LED

SW +12V FROM SW TO TOUCH PANEL FOR LEVEL

SW +12V FROM SW TO TOUCH PANEL FOR STORE

SWITCHED BATTERY FROM CONTROL BOX

CAN SHIELD

+12V ACC FROM TOUCH PANEL

GROUND FROM CONTROL BOX

WIRE DESCRIPTION AND FUNCTION

CAN HIGH
CAN LOW

PIN 4

PIN 1

MP85.2930

22FEB05

MANUAL

RETRACT

EXTEND

SEE: MP85.2930 & MP85.185J

SEE: MP85.2930 & MP85.185J & MP85.102K

SEE: MP85.185J

MASTER

WARNING

LEFT FRONT

LIGHT

SWITCH

PARK BRAKE

TOUCH PANEL - JACK WARNING LIGHTS AND PRESSURE SWITCHES

PILOT AIR DUMP - PARK BRAKE - MASTER WARNING LIGHT AND BUZZER

MP85.091C

9001 - TO
PARK BRAKE

7699

DIODE

7699

7699

9000

LIGHT

9000

7699

12 PIN
BLACK

BLACK

8 PIN

GRAY

4 PIN

BROWN

12 PIN

12 PIN
GREEN

12 PIN
GRAY

WARNING

DIAGRAM - 625 SERIES 

MANIFOLD - PUMP AND 
MASTER RELAYS

6230 - 6231

SWITCH

SEE ELECTRICAL CONNECTION 

LEVELING SYSTEM - LEVELING 

ELECTRICAL CONNECTION DIAGRAM

625 SERIES SINGLE STEP LEVELING SYSTEM

TO IGNITION

TO ACCESSORY

1000

6110

6111

DIODE

A

B

1200

5AMP

FUSE

BUZZER

6111

+

_

6235

SWITCH

PRESSURE

WARNING
SWITCH

UNDERSTAND OPERATOR’S MANUAL BEFORE USING. BLOCK FRAME AND TIRES

6120

CAUTION!

SECURELY BEFORE REMOVING TIRES OR CRAWLING UNDER VEHICLE.

EXTEND

RETRACT

HWH  COMPUTERIZED LEVELING

TOUCH PANEL

R

NOT IN
PARK/

SLOPE

EXCESS

AUTO
LEVEL

STOP

EMERGENCY

MODE

TRAVEL

STORE

AUTO

BRAKE

MANUAL

EXTEND

RETRACT

6235

2000

9301

9300

A

B

2200

RIGHT FRONT

PILOT DUMP
CONNECTION
BY OEM

PRESSURE

SWITCH

LEVELING MANIFOLD

ELECTRICAL CONNECTION DIAGRAM

625 SERIES LEVELING SYSTEM

PUMP AND MASTER RELAYS

LEVELING MANIFOLD

PUMP

MOTOR

MOTOR

#7

#6

PUMP
RELAY

#4

#5

TO PUMP

#9

+

8600

HWH GROUND

MANIFOLD

STUD

TO HWH GROUND STUD - 6240

TO 3000 LB PRESSURE SWITCH - 8100

TO 50 LB PRESSURE SWITCH - 8101

1400

4400
6240

6240

A

B

A

B

2400
7600

7601

B

A

A

B

3400

LEVELING

P.E.D

P.E.D

P.E.D

P.E.D

RF

RR

LR

LF

HARNESS

TOUCH PANEL

GROUND STUD

6230 - TO HWH

BLACK

8 PIN

MASTER
RELAY

#3

#1

BATTERY

#2

#8

8500

TO HOUSE

6800

14JUN05

MP85.102K

BROWN

GRAY

4 PIN

12 PIN

MP85.102K

suspension or PART 4 if not equipped with an air suspension.  Opposing yellow lights

a.   If the rest of PART 2 is OK, proceed to PART 3 if the vehicle is equipped with an air

are covered in PART 16.

5.   Opposing yellow level indicator light are on.

PF4

MP85.185J

LD26
LD27
LD28

LD39

R

R

LD36

T2

R
R

R

CN1

MP85.185J

08AUG07

LD38

R

R

LD37

G

LD33

ELECTRICAL CONNECTION DIAGRAM

CIRCUIT BOARD CONNECTOR AND PIN LOCATIONS

PF1

CR2

CN6

CR5

CR1

GND

1

12

LD21
LD22

LD24
LD25

LD23

CR6

CR7

R

LD29

CN9

Y
Y

Y
R

Y

R

LD32

G

Y

LD30

LD31

CR8

CR9

CR3

CR10

CR4

GND

GND

(SHIELD)

R

R

LD34

LD35

AUX

1

CH

CL

IGN

F10

8

IGN OUT

1

12

CN8

PF3

CN7

+12

CR11

12

1

CN3

from the 6120 wire in the 8 PIN black connector CN8.

be off when checking resistance on these wires.

box but could be the touch panel.  If the resistance is not correct, unplug the harness 

vehicle or the control box is not wired to the ignition circuit, remove power

link light at the touch panel.  If it is blinking, the touch panel is probably the problem.
If the link light is not blinking check the resistance between PIN 1 (yellow wire) and

from the touch panel.  Check the resistance between the yellow and green wire in the

the touch panel.  If the resistance between the harness pins is wrong,  unplug the 
touch panel cable (CN8-8 pin black connector) at the control box.  Check the 

If there is good voltage between PIN 4 and PIN 5 at the touch panel,

PIN 2 (green wire) at the touch panel with the harness plugged in.  The ignition must 

of resistance ± 7.5 ohms.  If the resistance is OK, the problem is probably the control

harness plug and between PIN 1 and PIN 2 of the panel plug. The resistance should
be 120 ohms ± 15 ohms.  If the resistance between the panel pins is wrong, replace 

resistance between PIN 7 (CL) and PIN 8 (CH) of CN8 in the control box.  If the 

resistance is OK (120 ohms ± 15 ohms), replace the touch panel cable.  If not 

There should be 60 ohms

NOTE: If the vehicle is a towable

check the

replace the control box.

Summary of Contents for 625S Series









































Reviews:

No comments

Brands by name

Popular brands

Load more brands