manualshive.com logo in svg

HWH 600 Series, Operator'S Manual, Page: 8 / 22

Share
Download
HWH 600 Series Operator'S Manual Download Page 8

MP35.9490

02FEB12

MANUAL ROOM RETRACT PROCEDURE

1. Retract jacks following the LEVELING SYSTEM RETRACT
PROCEDURE.

2. Locate the HYDRAULIC PUMP/MANIFOLD unit.

3. Open the SOLENOID VALVES by turning the "T" HANDLES
counterclockwise.

will become more difficult to turn as an internal spring is 
compressed.  Be sure to open both valves completely 
(about six turns of the "T" HANDLE).

are opened and internal pressure is released.

SOLENOID VALVES

"T"

HANDLES

(USE ONLY WHEN THE ROOM WILL NOT RETRACT WITH THE ROOM CONTROL SWITCH)

WINCH

WINCH STRAP

WINCH HANDLE

RATCHET LEVER

HOOK

MANUAL RETRACT WINCH

4. Locate the MANUAL RETRACT WINCH and connect it to
the room according to the vehicle manufacturer’s instructions.
To extend the WINCH STRAP firmly grasp WINCH HANDLE,
place RATCHET LEVER in its OFF position, and slowly rotate
the WINCH HANDLE counterclockwise, keeping a firm grip on
the handle. When enough WINCH STRAP is extended, place the
RATCHET LEVER in its ON position and slowly rotate the WINCH
HANDLE clockwise until the RATCHET LEVER locks.

5. Slowly winch the room in by turning the WINCH HANDLE
clockwise. The RATCHET LEVER should produce a loud, sharp,
clicking noise.

hydraulic fluid and make winching more difficult. 

WARNING:

ON

OFF

HYDRAULIC PUMP/MANIFOLD

NOTE : The room may move slightly as the SOLENOID VALVES

NOTE :

NOTE : Winching the room in quickly will raise pressure in the

NOTE : The "T" HANDLE may turn easily at first but

6. When the room is fully retracted, engage the room locking
devices.  Leave the retract winch in place.

WARNING:

THE ROOM EXTENSION SOLENOID VALVE

"T" HANDLES MUST BE IN THE OPEN POSITION WHEN THE
MANUAL RETRACT WINCH IS ENGAGED.

7. The system should be repaired before using again.

WARNING:

THE MANUAL RETRACT WINCH IS

EQUIPPED FOR MANUALLY RETRACTING THE ROOM
ONLY.  IT IS NOT TO BE USED FOR LIFTING OR ANY

When manually retracting the room, make sure the

jacks are retracted before retracting the room.

OTHER APPLICATION.  HIGH FORCES ARE CREATED
WHEN USING A WINCH, CREATING POTENTIAL SAFETY 
HAZARDS.  FAILURE TO FOLLOW ALL CAUTIONS AND
INSTRUCTIONS MAY CAUSE FAILURE OF THE MANUAL
RETRACT WINCH OR CONNECTIONS RESULTING IN
DAMAGE OR PERSONAL INJURY.  MAINTAIN FIRM GRIP 
ON THE WINCH HANDLE AT ALL TIMES.  NEVER RELEASE
THE HANDLE WHEN RATCHET LEVER IS IN THE OFF
POSITION AND THE WINCH IS LOADED.  THE WINCH
HANDLE COULD SPIN VIOLENTLY AND CAUSE PERSONAL
INJURY.  CHECK THE WINCH AND STRAPS FOR DAMAGE
OR WEAR, AND CHECK FOR PROPER RATCHET OPERATION
ON EACH USE OF THE WINCH.  DO NOT USE IF DAMAGED

OPERATE THE MANUAL RETRACT WINCH

BY HAND POWER ONLY.  IF THE WINCH CANNOT BE
CRANKED EASILY WITH ONE HAND IT IS PROBABLY OVER-
LOADED.  IF WINCHING BECOMES TOO DIFFICULT STOP
AND CHECK FOR OBSTRUCTIONS OR RESTRICTIONS ON
THE ROOM AND ROOM EXTENSION MECHANISM.

(WITH SOLENOID VALVES WITH VALVE RELEASE "T" HANDLES)

failure prevents the room from being retracted using the
CONTROL SWITCH.  For normal retract sequence see the
ROOM SLIDE RETRACT PROCEDURES.
vehicle manufacturer for storage location of the
retract device and information for connecting the
device to the room.

IMPORTANT: If the vehicle is not equipped with a winch,
DO NOT use other pulling devices to retract the room.
Follow steps 2 and 3 and try pushing the room in.
Contact the vehicle manufacturer or HWH Customer
Service at 1-800-321-3494 or 563-724-3396 for assistance.

The room can be retracted manually if a hydraulic or electric

OVERVIEW

Refer to the

OR WORN.

Summary of Contents for 600 Series























Reviews:

No comments