background image

EGPF Merchandisers

P/N 3143042_B 

1-1

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

UL LISTING

These merchandisers are manufactured to 
meet ANSI/ UL 471 standard requirements 
for safety. Proper installation is required to 
maintain the listing.

FEDERAL / STATE REGULATION

These merchandisers at the time they are 
manufactured, meet all federal and state/ 
provincial regulations. Proper installation 
is required to ensure these standards are 
maintained. 

Near the serial plate, each case carries a 
label identifying the environment for which 
the case was designed for use. For example:

ANSI/NSF-7 Type I

Display Refrigerator / Freezer intended 
for 75° F (24° C) / 55% RH Ambient 
Application

ANSI/NSF-7 Type II

Display Refrigerator / Freezer Intended for 
80° F / 55% RH Ambient Application

ANSI/NSF-7 

Display Refrigerator Intended for Bulk 
Produce

ABOUT THESE CASES

These cases are designed to be ready for 
remote installation of a top-mounted, air-
cooled condensing unit. See Section 2 of 
this manual for installation of field-installed 
condensing unit. 

The case is programmed for medium 
temperature use, and settings can be adjusted 
using the controller keypad. Lighting is not 
standard but offered as a option. 

LOCATION

These merchandisers are designed for 
displaying products in air conditioned 
stores where temperature is maintained at 
or below the ANSI/NSF-7 specified level 
and relative humidity is maintained at or 
below 55%. 

Placing refrigerated merchandisers in direct 
sunlight, near hot tables or near other heat 
sources could impair their efficiency.

Like other display cases, these are sensitive 
to air disturbances. Air currents passing 
around cases will seriously impair their 
operation. Do NOT allow air conditioning, 
electric fans, open doors or windows, etc. to 
create air currents around the cases.

Excessive ambient conditions may cause 
condensation and therefore sweating of 
doors. Facility operators should monitor 
doors and floor conditions to ensure safety 
of persons.

To prevent sweating on the exterior 
surfaces of merchandisers, there must be 

a

 

minimum

 

clearance

 

of

 4 

inches

 (102 

mm

)

 between the merchandisers and other 

fixtures or walls. Product should always 
be maintained at proper temperature. This 
means that from the time the product is 
received, through storage, preparation and 
display, the temperature of the product 
must be controlled to maximize the life of 
the product.

INSTALLATION

Summary of Contents for XR75CX

















































Reviews: