background image

IMPACT Rear Roll-in

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483  U.S.A.

P/N 0435045A

5-1

CARE AND CLEANING  

Long life and satisfactory performance of any
equipment is dependent upon the care it receives.
To ensure long life, proper sanitation and mini-
mum maintenance costs, these cases should be
thoroughly cleaned, all debris removed and the
interiors washed down, weekly. 

The store floor will be the interior display area of
the rear roll-in dairy cases. Since milk and other
spillage will occur, the floor should be cleaned
and sanitized at least once each week.

When cleaning, use caution to prevent water or
other liquids from entering the fan vents on the
interior side of the front assembly.

Exterior Surfaces

The exterior surfaces must be cleaned with a mild
detergent and warm water to protect and maintain
their attractive finish. 

N

EVER USE ABRASIVE

CLEANSERS OR SCOURING PADS

.

Interior Surfaces

The interior surfaces may be cleaned with most
domestic detergents, ammonia based cleaners and
sanitizing solutions with no harm to the surface.  

Do NOT Use:

• Abrasive cleansers and scouring pads, as these
will mar the finish.
• A hose on lighted shelves or submerge the
shelves in water.
• Solvent, oil or acidic based cleaners on any 
interior surfaces.
• Coarse paper towels on coated glass.
• Ammonia-based cleaners on acrylic parts.
• A hose on rail lights, canopy lights or any other
electrical connection.

STEAM OR HIGH WATER PRESSURE HOSES

TO WASH THE INTERIOR

.

T

HESE WILL DESTROY

THE CASES

’ 

SEALING CAUSING LEAKS AND POOR

PERFORMANCE

.

Do:

• Remove the product and all loose debris to
avoid clogging the waste outlet.
• Store product in a refrigerated area such as a 
cooler. Remove only as much product as can be
taken to the cooler in a timely manner.

• First turn off refrigeration, then disconnect
electrical power.

• Sweep the floor of the case.
• Thoroughly clean all surfaces with soap and hot
water. 

D

O NOT USE STEAM OR HIGH WATER

PRESSURE HOSES TO WASH THE INTERIOR

.

T

HESE WILL DESTROY THE CASES

’ 

SEALING

CAUSING LEAKS AND POOR PERFORMANCE

.

• Take care to minimize direct contact between
fan motors and cleaning or rinse water.
• Rinse with hot water, but do NOT flood.  

N

EVER INTRODUCE WATER FASTER THAN THE

WASTE OUTLET CAN REMOVE IT

.

• Allow cases to dry before resuming operation.
• Wipe down lighted shelves with a damp sponge
or cloth so that water does not enter the light 
channel.

D

O NOT USE A HOSE OR SUBMERGE

SHELVES IN WATER

.

Wipe dry.

• After cleaning is completed, turn on power to
the case.

MAINTENANCE

SHUT FANS OFF DURING 

CLEANING PROCESS.

WARNING

!

Do NOT allow product to sit in an

un-refrigerated area.

WARNING

!

Summary of Contents for IMPACT D5RRI



























Reviews: