Husqvarna TS 350E, Operator'S Manual

Page: 8 / 16

Operator’s manual - TS 350 E
Cutting method
Straight cuts (See fi g. 14)
• ≤ 570 mm : the stop (C) prevents fi ngers being trapped
between the table and the frame (See fi g. 15).
• > 570 et ≤ 650 mm : retract the stop (C) under the table
to increase the stroke.
A reversible and removable cutting guide enables 45° to
90° cuts to be made.
This cutting guide is machined in such a way that it can
be
fi tted in several positions in addition to its right angle
position from 0° to 45° to the left or to the right.
Depth of cut adjustment
(See fi g. 16)
• Slacken off handle (6).
• Use lever (5) to adjust the cutting height.
• Tighten handle (6).
Maintenance
(the motor must be stopped)
• Clean the machine regularly.
• Drain the tank (22) frequently to remove cutting resi-
due, which otherwise could block the pump and cause
it to wear out prematurely. (See
fi g. 17).
• Swill out the tanks (1) and (22) with water.
• Carefully clean the contact faces for the table rollers.
Store in a dry place, not accessible to children.
Maintain the tools carefully.
Fault fi nding
In the event of faulty operation refer to the tables below to
fi nd a solution.
The machine does not work
Causes Remedies
Not plugged in properly or
cable damaged Make sure that the supply is
correctly plugged in (plug,
extension lead, etc)
Check the supply cable
No mains voltage Test or have tested by an
electrician (circuit breaker,
plug, etc)
Switch defective, motor
cable damaged Have tested by an electri-
cian or contact the service
department
Motor faulty (no power,
unpleasant smell) Contact the service depart-
ment to have the motor
replaced
!
Diffi cult starting
Causes Remedies
Single phase motor starting
condenser Replace the condenser
Three-phase supply not
correct (on 2 phases, motor
cable faulty) Have it checked by an elec-
trician or contact the service
department
The pump does not start
Causes Remedies
The mains lead is not
correctly connected or is
damaged Check the mains lead
No voltage in pump circuit
or mains supply circuit Check the pump circuit and
mains supply circuit
The pump does not pump water
Causes Remedies
An air bubble may have
formed inside the pump
body Holding the pump of the
outlet pipe remove it from
the water and reimmerse it
The turbine is jammed Unscrew the fi lter and, using
a small screwdriver, remove
all dirt from the operating
area of the turbine.
Adjustments
• The machine is set before leaving the factory and no
adjustment is necessary.
• However, after shocks, loosening of nuts and bolts, or
sharp movements when tilting the head, if necessary
adjust the stop screws(D) and check the squareness
(for straight cuts) .
• To correct the bevel cutting setting, adjust the stop
screw (E) and lock the nut with a lock- nut (See fi g. 18).
• Ø 300 and Ø 350 adaptation (See fi g. 19)
A = Ø 300
B = Ø 350
Important advice
• Retighten the nuts and bolts periodically.
• In the event of a long period of use pay special atten-
tion to the maintenance and protection of the disc.
• Make sure that suf fi cient water is sprayed onto the
disc.
• Tighten the disc correctly.
• Make sure that the contact faces of the disc, the
fl anges and the spindle are clean.
The manufacturer declines all responsibil-
ity for loss or damage resulting from misuse
or any modifi cation, alteration or powering
that does not conform to the manufacturer’s
original specifi cations.
!
8
- Polish