Husqvarna TC 50 2023 Owner'S Manual Download

Page: 77 / 196

SERVICE WORK ON THE CHASSIS 11

11.46

Checking the throttle cable routing

Warning

Danger of accidents

The throttle cable can become kinked, trapped or blocked if it is not routed cor-

rectly.

If the throttle cable is kinked, trapped or blocked, the speed can no longer be controlled.

–

Make sure that the throttle cable routing and the play in throttle cable complies with the specifica-

tion.

Preparatory work

–

Remove the seat. (

p. 62)

–

Remove the left side cover. (

p. 58)

–

Remove the right side cover. (

p. 56)

–

Turn the knurled screw on the fuel tap all the way clockwise.

–

Remove the fuel tank.

(

p. 53)

V02081-01

Main work

–

Check the throttle cable routing.

The throttle cable must be routed to the carburetor behind

the handlebars and above the fuel tank bracket.

» If the throttle cable is not routed as specified:

–

Correct the throttle cable routing.

Finishing work

–

Install the fuel tank.

(

p. 54)

–

Install the left side cover. (

p. 59)

–

Install the right side cover. (

p. 57)

–

Mount the seat. (

p. 62)

11.47

Checking the rubber grip

401197-01

–

Check the rubber grips on the handlebar for damage, wear,

and looseness.
» If a rubber grip is damaged, worn, or loose:

–

Change the rubber grip.

Rubber grip adhesive (00062030051) (

p. 140)

–

Additionally secure the rubber grip. (

p. 76)

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands