background image

14 – 

English

FUEL HANDLING

Fuel

CAUTION! The machine is equipped with a two-stroke engine 
and must always been run using a mixture of petrol and two-
stroke engine oil. It is important to accurately measure the 
amount of oil to be mixed to ensure that the correct mixture is 
obtained. When mixing small amounts of fuel, even small 
inaccuracies can drastically affect the ratio of the mixture.

Petrol

Use good quality unleaded or leaded petrol.

The lowest octane recommended is 90 (RON). If you run 
the engine on a lower octane grade than 90 so-called 
knocking can occur. This gives rise to a high engine 
temperature, which can result in serious engine damage.

Two-stroke oil

For best results and performance use HUSQVARNA two-
stroke engine oil, which is specially formulated for our air-
cooled two-stroke engines.

Never use two-stroke oil intended for water-cooled 
engines, sometimes referred to as outboard oil (rated 
TCW).

Never use oil intended for four-stroke engines.

Mixing ratio

1:50 (2%) with HUSQVARNA two-stroke oil or equivalent.

1:33 (3%) with oils class JASO FB or ISO EGB formulated for 
air-cooled, two-stroke engines.

Mixing

Always mix the petrol and oil in a clean container intended 
for fuel.

Always start by filling half the amount of the petrol to be 
used. Then add the entire amount of oil. Mix (shake) the 
fuel mixture. Add the remaining amount of petrol.

Mix (shake) the fuel mixture thoroughly before filling the 
machine’s fuel tank.

Do not mix more than one month’s supply of fuel at a time.

If the machine is not used for some time the fuel tank 
should be emptied and cleaned.

Fuelling

Keep the handle dry and free from oil and fuel.

Ensure that the fuel is well mixed by shaking the container 
before filling the tank.

Always exercise care when refilling the fuel. Move the 
machine at least three metres from the fuelling area 
before it is started. Check that the fuel cap is tightened 
correctly.

Clean around the fuel cap. Clean the fuel and oil tank 
regularly. The fuel filter should be changed at least once a 
year. Contamination in the tanks causes malfunction.

!

WARNING! Always ensure there is adequate 
ventilation when handling fuel.

Petrol, litre

Two-stroke oil, litre

2% (1:50)

3% (1:33)

5

0,10

0,15

10

0,20

0,30

15

0,30

0,45

20

0,40

0,60

!

WARNING! Taking the following precautions, 
will lessen the risk of fire:

Do not smoke or place hot objects near fuel.

Always shut off the engine before refuelling.

When refuelling, open the fuel cap slowly so 
that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the machine away from the 
refuelling area before starting.

Summary of Contents for K1250

























Reviews: