background image

English

 – 17

MAINTENANCE

Fuel filter

The fuel filter sits inside the fuel tank.

The fuel tank must be protected from contamination when 
filling. This reduces the risk of operating disturbances 
caused by blockage of the fuel filter located inside the 
tank.

The filter cannot be cleaned but must be replaced with a 
new filter when it is clogged. 

The filter should be 

changed at least once per year.

Air filter

Air filters must be regularly cleaned to remove dust and dirt in 
order to avoid:

Carburettor malfunctions

Starting problems

Loss of engine power

Unnecessary wear to engine parts.

Excessive fuel consumption.

The air filter system consists of an oiled foam plastic filter (1) 
and a paper filter (2):

1

The foam plastic filter is easily accessible under the filter 
cover A. This filter should be checked weekly and 
replaced if necessary. In order to obtain a good filtering 
effect, the filter must be replaced regularly or cleaned and 
oiled. A special HUSQVARNA oil has been produced for 
this purpose.

Remove the foam plastic filter. Wash the filter well in tepid 
soapy water. After cleaning, rinse the filter well in clean 
water. Squeeze out and allow the filter to dry. NOTE! High 
pressure compressed air can damage the foam.

Put the filter in a plastic bag and pour the filter oil over it. 
Knead the plastic bag to distribute the oil. Squeeze the 
excess oil out of the filter inside the plastic bag and pour 
off the excess before fitting the filter to the machine. Never 
use common engine oil. This would drain through the filter 
quite quickly and collect in the bottom.

2

The paper filter is accessible under cover B. This filter 
must be replaced/cleaned when the engine’s power drops 
or after one-two weeks. The filter is cleaned by shaking or 
by careful blowing with compressed air. Note that the filter 
must not be washed.

An air filter that has been in use for a long time cannot be 
cleaned completely. The filter must therefore be replaced with 
a new one at regular intervals. 

A damaged air filter must 

always be replaced.

A

B

IMPORTANT INFORMATION

Poor maintenance of the air filter will cause carbon build-up 
on the spark plug and abnormal wear to engine parts.

Summary of Contents for K1250

























Reviews: