4. Fill the oil tank and do a check of the oil level. See
To fill and change the engine oil on page 12
.
To fill fuel
If available, use low-emission/alkylate gasoline. If low-
emission/alkylate gasoline is not available, use good
quality unleaded gasoline or leaded gasoline. Use
gasoline with octane number not less than 90 (87 AKI)
and with a maximum of 10% ethanol (E10).
CAUTION: Do not use gasoline with an
octane number less than 90 RON (87 AKI).
This can cause damage to the product.
1. Open the fuel tank cap slowly to release the
pressure.
2. Fill slowly with a fuel can. If you spill fuel, remove it
with a cloth and let remaining fuel dry off.
3. Clean the area around the fuel tank cap.
4. Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
5. Move the product a minimum of 3 m (10 ft) from the
position where you filled the tank, before a start.
To set the handle position
1. Lift the hook (A).(Fig. 24 )
2. Push the hook forward to set the handle in park
position (B).
3. Pull the hook rearward to set the handle in mow
position (C).
To start the product
1. Make sure that the ignition cable is connected to the
spark plug.
2. Set the handle in park position, see
To set the
handle position on page 10
.
3. Open the fuel valve.(Fig. 25 )
4. Adjust the choke control.
a) If the engine is cold, set the choke control to the
choke position.(Fig. 26 )
b) If the engine is warm, set the choke control to the
operation position.(Fig. 27 )
5. Hold the engine brake handle against the handlebar.
6. Put your right foot on the cutting cover.
7. Hold the top of the lower handle with your right hand
and tilt the product.
8. Hold the starter rope handle with your right hand.
(Fig. 28 )
9. Slowly pull out the starter rope until you feel some
resistance.
10. Pull with force to start the engine.
11. When the engine is at full speed, carefully lower the
product to the ground.
12. When the engine is warm, make sure that the choke
control is set to operation position.
13. Set the handle in mow position, see
To set the
handle position on page 10
.
WARNING: Do not twist the starter rope
around your hand.
To stop the product
• Tilt the product and release the engine brake handle.
• When the engine stops, lower the product.
• Set the handle in park position, see
To set the
handle position on page 10
.
• Close the fuel valve.
To get a good result
• Always use a sharp blade. A blunt blade gives an
irregular result and the cut surface of the grass
becomes yellow. A sharp blade also uses less
energy than a blunt blade.
• Do not cut more than ⅓ of the length of the grass.
Cut first with the cutting height set high. Examine the
result and lower the cutting height to an applicable
level. If the grass is very long, drive slowly and cut 2
times if necessary.
• Cut in different directions each time to prevent
stripes in the lawn.
Maintenance
Introduction
WARNING: Before you do maintenance, you
must read and understand the safety
chapter.
For all servicing and repair work on the product, special
training is necessary. We guarantee the availability of
professional repairs and servicing. If your dealer is not a
service agent, speak to them for information about the
nearest service agent.
Before you do maintenance work
WARNING: To prevent injury and damage to
the product, obey these instructions when it
is necessary to put the product on its side.
1. Close the fuel valve.(Fig. 29 )
10
504 - 003 - 26.01.2018
Summary of Contents for Flymo XL500
