Husqvarna FE 450 Owner'S Manual Download Page 99

Page: 99 / 128

17 TUNING THE ENGINE

17.1

Checking the play in the throttle cable

400192-11

–

Check the throttle grip for smooth operation.

–

Move the handlebar to the straight-ahead position. Turn the throttle grip back and
forth slightly and determine the play in throttle cable



Play in throttle cable

3… 5 mm (0.12… 0.2 in)

» If the throttle cable play does not meet the specified value:

–

Adjust the play in the throttle cable.

(

p. 97)

–

Push the cold start button in all the way.

When the throttle grip is turned forward, the cold start button returns to its orig-

inal position.

» If the cold start button does not return to its original position:

–

Adjust the play in the throttle cable.

(

p. 97)

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may

result in unconsciousness and death.

–

Always make sure there is sufficient ventilation when running the

engine.

–

Use an effective exhaust extraction system when starting or running

the engine in an enclosed space.

–

Start the engine and let it run idle. Move the handlebar to and fro over the entire

steering range.

The idle speed must not change.

» If the idle speed changes:

–

Adjust the play in the throttle cable.

(

p. 97)

17.2

Adjusting the play in the throttle cable

Info

If the correct routing of the throttle cables has already been secured, the fuel tank does not need to be removed.

Preparatory work

–

Remove the air filter box cover. (

p. 56)

–

Remove the seat. (

p. 55)

–

Remove the fuel tank.

(

p. 60)

–

Check throttle cable routing. (

p. 67)

F00450-10

Main work

–

Move the handlebar to the straight-ahead position.

–

Push back sleeve



–

Loosen nut



–

Turn adjusting screw



in as far as possible.

–

Loosen nut



–

Push cold start button



all the way to the stop.

–

Turn adjusting screw



so that the cold start button moves to the basic position

when the throttle grip is turned to the front.

–

Tighten nut



–

Turn adjusting screw



so that there is play in the throttle cable at the throttle

grip.
Guideline

Play in throttle cable

3… 5 mm (0.12… 0.2 in)

–

Tighten nut



–

Slide on sleeve



Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands