Husqvarna 966042601 Operator'S Manual Download Page 33 | Manualshive

Page: 33 / 56

background image

MAINTENANCE

34 -

HUSQVARNA

Cyclone Filter

The cyclone filter collects the largest contaminant

particles, which collect in the container. When you can

see a layer of dirt at the bottom of the container, the

cyclone housing (1), air channels and air intake screen

(2) must be cleaned.

IMPORTANT INFORMATION
Exercise care when reassembling to avoid

damage.
Make sure when mounting that the air intake

screen fits exactly in its guide in the upper

portion.
Make sure the air channel ends up in the

proper position.

8011-126

1

2

8011-213

Remove the three screw holding the cyclone housing.

Remove the housing with the air intake screen and

remove the air channels.
The air channels may remain in the upper portion or

follow along with the housing when removed.

8011-212

Clean the components, using warm water, mild

detergent and a sift brush. Dry carefully.

Refit the components. Place the air channels in the

cyclone housing. Insert cyclone housing into position

and make sure it fits in the upper portion. DO NOT

use force; rather coax it into place before refitting the

screws.

«
...
31
32
33
34
35
...
»

Summary of Contents for 966042601

























































Reviews:

No comments

Related manuals for 966042601

Brand: Parkside Pages: 60

Brand: Varia Pages: 12

Brand: stayer Pages: 10

Brand: Optimum Pages: 47

Brand: Jet Pages: 20

Brand: Far Tools Pages: 32

Brand: Protool Pages: 148

Brand: Metabo HPT Pages: 44

Brand: Au Tour du Béton Pages: 13

Brand: Skil Pages: 64

Brand: King Canada Pages: 4

Brand: Adler Europe Pages: 48

Brand: AGP Pages: 16

Brand: Jula Pages: 35

Brand: Chicago Electric Pages: 7

Brand: Scheppach Pages: 120

Brand: STI Pages: 36

Brand: Alpha tools Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands