Husqvarna 966042601 Operator'S Manual Download Page 12

Page: 12 / 56

SAFETY

HUSQVARNA

-13

Maintenance

Never make adjustments with the engine running.

•

Disengage the drive units, shut off the engine and

•

wait until all moving parts come to a complete

stop before making adjustments, performing

maintenance or cleaning the machine.
Disconnect the spark plug cable before beginning

•

repair work.
Keep all components in serviceable condition and

•

make sure all nuts, bolts and other hardware are

tight. Replace worn or damaged decals.
Be careful when checking work tools. Use gloves

•

when performing maintenance work.
Never allow persons not trained in the use of the

•

machine to perform service on it.
Always park the machine on even ground before

•

performing maintenance or making adjustments.
Do not disassemble the engine. This can

•

invalidate the engine warranty. Contact the dealer

for questions regarding service or guarantee

matters. Follow all maintenance instructions.
Do not change the setting of governors and avoid

•

running the engine with overly high RPM. If the

engine is run too fast, damage to the machine

components can occur.
Do not modify safety equipment. Check regularly

•

to be sure it works properly. The machine must

not be run with defective or disassembled safety

equipment.

The muffler is designed to maintain sound levels at

•

an approved level and keep direct exhaust away

from the user. Exhaust gases from the engine are

extremely hot and may contain sparks that can

cause fires or burn the user.
Never use a machine with a defective muffler.

•

Reduce the risk of fire by removing grass, leaves

•

and other debris that may have caught in the

machine.

8011-027

Remove the spark plug cable.

8011-210c

Keep the machine clean.

WARNING!
Wait until all moving parts are

completely still before performing

maintenance on the machine. Turn

off the engine and remove the spark

plug cable.

Summary of Contents for 966042601

























































Search results

Summary of Contents for 966042601

Reviews:

Related manuals for 966042601

Brands by name

Popular brands

Husqvarna 966042601, Operator'S Manual

Search results

Summary of Contents for 966042601

Reviews:

Related manuals for 966042601

Brands by name

Popular brands