Husqvarna 550H EPOS Operator'S Manual Download Page 15

Page: 15 / 44

3.8 Installation of the product

3.8.1 General steps for installation of the

product

For full instructions follow the installation instructions in

Installation of the product on page 15

Install the reference station.

Install the charging station.

Install the Automower

Connect app to your

mobile device.

Pair the product with the Automower

Connect

app. Do the basic settings in the start up sequence

in the Automower

Connect app.

Make a map with work areas, stay-out zones,

transport paths and point of interests.

Use Automower

Connect app to do settings for

the product.

3.8.2 Installation tools

•

Hex key, 8 mm. Included in the carton.

3.8.3 Installation of the charging station

Read and understand the instructions about the

charging station. Refer to

To examine where to put the

charging station on page 12

WARNING:

Obey national regulations

about electrical safety.

WARNING:

The product is only to be

used with the power supply unit supplied by

Husqvarna.

WARNING:

Do not put the power

supply at a position where there is a risk that

it can become wet. Do not put the power

supply on the ground.

WARNING:

Do not encapsulate the

power supply. Condensed water can harm

the power supply and increase the risk of

electrical shock.

WARNING:

Risk of Electric Shock.

Install only to an residual-current device

(RCD) with a tripping current of maximum 30

mA when connecting the power supply to

the wall socket. Applicable to USA/Canada.

If power supply is installed outdoors: Risk of

Electric Shock. Install only to a covered

Class A GFCI receptacle (RCD) that has an

enclosure that is weatherproof with the

attachment plug cap inserted or removed.

CAUTION:

Do not make new holes in

the charging station plate.

CAUTION:

Do not put your feet on the

baseplate of the charging station.

WARNING:

The power supply cable

and extension cable must be outside the

work area to avoid damage to the cables.

When connecting the power supply, only use a power

outlet that is connected to an residual current device

(RCD).

3.8.3.1 To install the charging station

Put the charging station in the selected area.

Attach the charging station to the ground with the

supplied screws.

Connect the low-voltage cable to the charging

station.

Put the power supply at a minimum height of 30

cm / 12 in. Refer to

To examine where to put the

power supply on page 13

min 30 cm / 12”

Connect the power supply cable to a 100-240V

power outlet.

Put the low-voltage cable in the ground outside the

work area. Use stakes or bury the cable.

Put the product in the charging station to charge

the product.

3.8.3.2 To do a visual check of the charging station
1.

Make sure that the indicator LED lamp on the

charging station has a green light.

1619 - 002 - 19.01.2021

Installation - 15

Summary of Contents for 550H EPOS












































Search results

Summary of Contents for 550H EPOS

Reviews:

Husqvarna 550H EPOS, Operator'S Manual, Page: 15 / 44

Search results

Summary of Contents for 550H EPOS

Reviews: