Husqvarna 550H EPOS Operator'S Manual Download Page 11 | Manualshive

Page: 11 / 44

Husqvarna 550H EPOS Operator'S Manual Download Page 11

2.3.3.1 How to lift the product
1.

Push the STOP button to stop the product.

2.

Set the Main switch in position

0

.

3.

Carry the product by the handle with the blade disc

away from your body.

2.3.4 Maintenance

WARNING:

When the product is turned

upside down the Main switch must always

be in the

0

position.

The Main switch should be set in the

0

position before all work on the chassis of the

product, such as cleaning or replacing the

blades.

CAUTION:

Never use a high-pressure

washer or even running water to clean the

product, charging station and reference

station. Never use solvents for cleaning.

CAUTION:

Use the plug to disconnect

the charging station before any cleaning or

maintenance of the charging station.

Inspect the product each week and replace any

damaged or worn parts. Refer to

Maintenance on page

25

.

2.3.5 In the event of a thunderstorm

To decrease the risk of damage to electrical

components in the product and the charging station, we

recommend that the power supplies to the charging

station and reference station are disconnected if there is

a risk of a thunderstorm. Connect the power supplies

again when there is not a risk of thunderstorm.

1619 - 002 - 19.01.2021

Safety - 11

«
...
9
10
11
12
13
...
»

Summary of Contents for 550H EPOS













































Reviews:

No comments