background image

MAINTENANCE

18 – English

Muffler

CAUTION! 

 Some mufflers are fitted with a catalytic 

converter. See chapter on Technical data to see whether 
your machine is fitted with a catalytic converter.

The muffler is designed to reduce the noise level and to 
direct the exhaust gases away from the operator. The 
exhaust gases are hot and can contain sparks, which may 
cause fire if directed against dry and combustible 
material.

Some mufflers are equipped with a special spark arrestor 
mesh. If your machine has this type of muffler, you should 
clean the mesh at least once a week. This is best done 
with a wire brush.

On mufflers without a catalytic converter the mesh should 
be cleaned weekly, or replaced if necessary. On mufflers 
fitted with a catalytic converter the mesh should be 
checked, and if necessary cleaned, monthly. 

If the mesh 

is damaged it should be replaced.

 If the mesh is 

frequently blocked, this can be a sign that the 
performance of the catalytic converter is impaired. 
Contact your dealer to inspect the muffler. A blocked 
mesh will cause the machine to overheat and result in 
damage to the cylinder and piston. See also instructions 
under the heading Maintenance.

CAUTION! 

 Never use a machine with a defective muffler.

Cooling system

To keep the working temperature as low as possible the 
machine is equipped with a cooling system.

The cooling system consists of:

1

Air intake on the starter.

2

Fins on the flywheel.

3

Cooling fins on the cylinder.

4

Cylinder cover (directs cold air over the cylinder).

Clean the cooling system with a brush once a week, more 
often in demanding conditions. A dirty or blocked cooling 
system results in the machine overheating which causes 
damage to the piston and cylinder.

Spark plug

The spark plug condition is influenced by:

Incorrect carburettor adjustment.

An incorrect fuel mixture (too much or incorrect type 
of oil).

A dirty air filter.

These factors cause deposits on the spark plug 
electrodes, which may result in operating problems and 
starting difficulties.

If the machine is low on power, difficult to start or runs 
poorly at idle speed: always check the spark plug first 

!

WARNING! Mufflers fitted with catalytic 
converters get very hot during use and 
remain so for some time after stopping. 
This also applies at idle speed. Contact 
can result in burns to the skin. 
Remember the risk of fire!

1 2

3

4

Summary of Contents for 325HS75 X-series





























Reviews: