McCulloch MT3075 User Manual Download

Page: 1 / 26

PN 9096-334601

Printed in Taiwan

Models : MT3075/ MT3090/MT30775/ MT30790

WARNING • PLEASE READ

For your own safety please read this manual before attempting to operate your new unit. Failure to fol-
low instructions can result in serious personal injury. Spend a few moments to familiarize yourself with
your trimmer before each use.

MT3075

MT3090

MT30775

MT30790

USER MANUAL

Gas String Trimmers/Brushcutters

U.S.A. Imported by:
MTD LLC
P.O. Box 361131
Cleveland, OH 44136-0019

Canada Imported by / Importé par:
MTD PRODUCTS
97 Kent Avenue
Kitchener, ON
CANADA N2G 4J1

Made in Taiwan / Fabriquè à Taïwan/ Hecho en Taiwan

STOP

ARRÊT

ALTO

For problems or questions, DO NOT return

this product to the store. Contact your

Customer Service Agent .

En cas de problèmes ou pour des questions,

NE PAS retourner ce produit au point de vente. S'adresser

au préposé du Service à la clientèle en composant.

Para problemas o preguntas, NO devolver este producto a la tienda

Contacte a su Agente de Servicio al Cliente.

U.S.A. 1-866-747-9816

CANADA 1-800-668-1238

For Consumer Assistance Please Call

L'Aide Du Consommateur Necessitez S'il Vous Plait

Para La Ayuda Del Consumidor Llame Por Favor

Summary of Contents for MT3075



























Search results

Summary of Contents for MT3075

Reviews:

Related manuals for MT3075

Brands by name

Popular brands

McCulloch MT3075, User Manual

Search results

Summary of Contents for MT3075

Reviews:

Related manuals for MT3075

Brands by name

Popular brands