Husqvarna 2007 HUV 4213-G Owner'S Manual Download Page 36 | Manualshive

Page: 36 / 48

background image

Battery

Page 34

2007 HUV4213 Gasoline Vehicle Owner’s Manual

NOTE: Whenever possible, avoid using oxygenated fuels and fuels that are blended with alcohol. Vehicles

to be stored for extended periods should be prepared for storage as instructed. See Preparing the
Vehicle for Extended Storage on page 23.

3. Replace fuel cap on the tank. Ensure cap is tightened securely.

4. Clean any spilled fuel from the tank top and around the tank area.

5. Replace passenger seat.

ý

WARNING

• Make sure seat hinges and latch are securely engaged before operating vehicle.

BATTERY

See General Warnings on page 10.

ý

DANGER

• Battery – Explosive gases! Do not smoke. Keep sparks and flames away from the vehicle and

service area. Ventilate when charging or operating vehicle in an enclosed area. Wear a full
face shield and rubber gloves when working on or near batteries.

• Tools, wires, and metal objects can cause sparks when shorted across a battery.

• Follow all instructions carefully when working with batteries.

• Charge battery in a well-ventilated area only.

• Battery – Poison! Contains acid! Causes severe burns. Avoid contact with skin, eyes, or

clothing. Antidotes:

- External: Flush with water. Call a physician immediately.

- Internal: Drink large quantities of milk or water followed with milk of magnesia or vegetable

oil. Call a physician immediately.

- Eyes: Flush with water for 15 minutes. Call a physician immediately.

Figure 24 Fuel Tank – HUV4213

TO CARBURETOR

VENT TUBE

VENT

FUEL
TANK

FUEL
SHUT-OFF
VALVE

«
...
34
35
36
37
38
...
»

Summary of Contents for 2007 HUV 4213-G

















































Reviews:

No comments

Related manuals for 2007 HUV 4213-G

Brand: Taylor-Dunn Pages: 126

POLARIS SPORTSMAN 400

Brand: Peg-Perego Pages: 40

Brand: Baja motorsports Pages: 8

Brand: Terra Cat Pages: 12

Stalwart Carry Fold 2

Brand: M-WAVE Pages: 6

Brand: Federal Signal Corporation Pages: 140

Brand: Landoll Pages: 88

Brand: HAUL MASTER Pages: 22

Brand: HAUL MASTER Pages: 28

Brand: Yamaha Pages: 112

FTK 4000 Series

Brand: Humbaur Pages: 20

Brand: Yamaha Pages: 468

Brand: Wood-mizer Pages: 90

Brand: Toro Pages: 4

Brand: Toro Pages: 2

Brand: Toro Pages: 8

Brand: Toro Pages: 36

Brand: Toro Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands