Husqvarna 2007 HUV 4213-G Owner'S Manual Download Page 26 | Manualshive

Page: 26 / 48

background image

Storage

Page 24

2007 HUV4213 Gasoline Vehicle Owner’s Manual

7. Disconnect the battery cables, negative (–) cable first.

See WARNING “To avoid unintentionally start-

ing...” on page 10.

8. Batteries should be clean and free of corrosion. Wash tops and terminals of batteries with a solution of

baking soda and water (1 cup (237 mL) baking soda per 1 gallon (3.8 L) of water). Rinse solution off bat-
teries. Do not allow this solution to enter the batteries. Be sure terminals are tight. Let the terminals dry
and then coat them with Battery Terminal Protector Spray (P/N 603 00 00-03).

9. To protect the engine, remove spark plug and pour 1/2 ounce (14.2 mL) of SAE 10 weight oil into the

engine through the spark plug hole. Rotate engine crankshaft by hand several times and then install the
spark plug.

10. Lower the passenger side seat.

11. Lower the cargo bed.

See WARNING “For vehicles with cargo beds...” on page 10.

12. Adjust tires to recommended tire pressure.

See Vehicle Specifications on page 38.

13. Perform semiannual periodic lubrication.

See Periodic Lubrication Schedule on page 28.

14. Thoroughly clean front body, rear body, seats, cargo bed, engine compartment, and underside of vehicle.

15. Do not engage the park brake. Chock the wheels to prevent the vehicle from rolling.

RETURNING THE STORED VEHICLE TO SERVICE

1. Make sure the key switch is in the OFF position and the Forward/Reverse handle is in the NEUTRAL

position. Chock the wheels.

2. Access the battery compartment.

See WARNING “For vehicles with cargo beds...” on page 10.

3. Tilt the bed and ensure that the prop rod is properly engaged.

See WARNING “For vehicles with cargo

beds...” on page 10.

4. Lift the passenger seat.

5. Restore fuel system to operation.

See

Figure 24

on page 34

.

5.1. Remove plug from fuel tank vent.

5.2. Connect vent tube to fuel tank vent.

Figure 12 Fuel Shut-off Valve – Closed Position

CLOSED (OFF) POSITION

(SELECTOR IS ALIGNED

WITH OFF MARKINGS ON THE SIDES OF VALVE)

OFF

OFF

VIEWED FROM SELECTOR

SIDE OF VALVE

«
...
24
25
26
27
28
...
»

Summary of Contents for 2007 HUV 4213-G

















































Reviews:

No comments

Related manuals for 2007 HUV 4213-G

Brand: Hamron Pages: 12

Brand: Polaris Pages: 215

PAVER SPECIAL RPS Series

Brand: Etnyre Pages: 61

Brand: Snapper Pages: 6

Brand: Snapper Pages: 8

Brand: Snapper Pages: 36

Brand: Strongway Pages: 16

Brand: Ventrac Pages: 59

Brand: Traxxas Pages: 26

Chem-Veyor 2614D

Brand: Walinga Pages: 28

Brand: Landoll Pages: 36

1966 Snow Cruiser C-1560

Brand: OMC Pages: 20

Brand: Malone Pages: 4

Grizzly 700 2011

Brand: Yamaha Pages: 172

Brand: MANCO Pages: 20

Brand: Tao Motor Pages: 80

Brand: Ski-Doo Pages: 34

Legend SE 800 SDI 2003

Brand: Ski-Doo Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands