Husqvarna 2007 HUV 4213-G Owner'S Manual Download Page 35

Page: 35 / 48

Fueling Instructions

2007 HUV4213 Gasoline Vehicle Owner’s Manual

Page 33

OIL VISCOSITY

Choose the viscosity according to the temperature as shown in the oil viscosity chart

(Figure 23)

NOTE: Using multi-grade oils (5W-20, 10W-30, and 10W-40) will increase oil consumption. Check oil level

more frequently when using them.

FUELING INSTRUCTIONS

See General Warnings on page 10.

DANGER

• Turn the key switch to the OFF position before fueling.

• Never pour gasoline into the fuel tank when the engine is hot or while it is running.

• To avoid electric arc caused by static electricity, the fuel storage/pumping device must be

grounded. If the pump is not grounded, the vehicle must be grounded to the pump before and
during the fueling operation.

• If the vehicle has an all-weather enclosure installed, be sure the fuel tank is properly vented as

shown (Figure 24, Page 34).

• To avoid the possibility of fire, clean up any spilled gasoline before operating the vehicle.

CAUT ION

• To allow for expansion, do not fill higher than one inch (2.54 cm) from the top of the fuel tank.

Avoid spilling fuel.

1. Remove the passenger seat.

2. Remove fuel cap and fill tank with fresh unleaded gasoline only.

See preceding DANGER and CAU-

TION.

Figure 23 Oil Viscosity Chart

SAE 5W-20

SAE 10W-30/SAE 10W-40

SAE 30

SAE 40

-20° C -10° C

0° C

10° C

20° C 30° C

40° C

-4° F

14° F

32° F

50° F

68° F 86° F

104° F

Summary of Contents for 2007 HUV 4213-G

















































Search results

Summary of Contents for 2007 HUV 4213-G

Reviews:

Related manuals for 2007 HUV 4213-G

Brands by name

Popular brands

Husqvarna 2007 HUV 4213-G, Owner'S Manual

Search results

Summary of Contents for 2007 HUV 4213-G

Reviews:

Related manuals for 2007 HUV 4213-G

Brands by name

Popular brands