Husqvarna 2005 HUV4213 Owner'S Manual Download Page 35

Page: 35 / 46

Battery

2005 HUV4213 Gasoline Vehicle Owner’s Manual

Page 33

WARNING

• Do not jump-start a dead battery using another battery and jumper cables.

The battery in a Husqvarna vehicle is a 12-volt, low-maintenance battery that requires infrequent checks

(Figure 25)

. Electrolyte level should be checked semiannually.

1. Turn the key switch to the OFF position and remove the key. Place the Forward/Reverse handle in the

NEUTRAL position. Chock the wheels.

2. Access the engine compartment.

See WARNING “For vehicles with cargo beds...” on page 8.

3. Tilt the bed and ensure that the prop rod is properly engaged.

4. Disconnect the battery cables, negative (–) cable first.

See WARNING “To avoid unintentionally start-

ing...” on page 8.

5. Use a flat blade screwdriver, and carefully remove the battery cell caps from the battery

(Figure 25)

See

following WARNING.

WARNING

• Wear safety glasses or approved eye protection when servicing the vehicle. Wear a full face

shield and rubber gloves when working on or near batteries.

6. Carefully check the electrolyte level and add distilled water if necessary. Do not fill above designated fill

line. Replace battery cell caps.

7. Clean both battery terminals with a solution of baking soda and water (1 cup (237 mL) baking soda per

1 gallon (3.8 L) of water). Rinse thoroughly. Do not allow this solution to enter the battery. Tighten battery
terminals to 20 ft-lb (27.1 N·m). Let the terminals dry and then spray them with Battery Terminal Protector
Spray (P/N 603 00 00-03).

See following CAUTION.

CAUTION

• If battery wire terminals are damaged or corroded, replace or clean them as necessary. Failure

to do so may cause them to overheat during operation.

Figure 25 Battery

Figure 26 Battery Electrolyte Level

ELECTROLYTE

LEVEL AT LEAST

1/2-INCH (13 MM)

ABOVE

PLATES OR

TO LEVEL

INDICATOR

PLATES

LEVEL

INDICATOR

BATTERY
CAP

Summary of Contents for 2005 HUV4213















































Search results

Summary of Contents for 2005 HUV4213

Reviews:

Related manuals for 2005 HUV4213

Brands by name

Popular brands

Husqvarna 2005 HUV4213, Owner'S Manual

Search results

Summary of Contents for 2005 HUV4213

Reviews:

Related manuals for 2005 HUV4213

Brands by name

Popular brands