Husqvarna 2005 HUV4213 Owner'S Manual Download Page 24 | Manualshive

Page: 24 / 46

background image

Storage

Page 22

2005 HUV4213 Gasoline Vehicle Owner’s Manual

7. Disconnect the battery cables, negative (–) cable first.

See WARNING “To avoid unintentionally start-

ing...” on page 8.

8. Batteries should be clean and free of corrosion. Wash tops and terminals of batteries with a solution of

baking soda and water (1 cup (237 mL) baking soda per 1 gallon (3.8 L) of water). Rinse solution off bat-
teries. Do not allow this solution to enter the batteries. Be sure terminals are tight. Let the terminals dry
and then coat them with Battery Terminal Protector Spray (P/N 603 00 00-03).

9. To protect the engine, remove spark plug and pour 1/2 ounce (14.2 mL) of SAE 10 weight oil into the

engine through the spark plug hole. Rotate engine crankshaft by hand several times and then install the
spark plug.

10. Lower the passenger side seat.

11. Lower the cargo bed.

See WARNING “For vehicles with cargo beds...” on page 8.

12. Adjust tires to recommended tire pressure.

See Vehicle Specifications on page 36.

13. Perform semiannual periodic lubrication.

See Periodic Lubrication Schedule on page 26.

14. Thoroughly clean front body, rear body, seats, cargo bed, engine compartment, and underside of vehicle.

15. Do not engage the park brake. Chock the wheels to prevent the vehicle from rolling.

RETURNING THE STORED VEHICLE TO SERVICE

1. Make sure the key switch is in the OFF position and the Forward/Reverse handle is in the NEUTRAL

position. Chock the wheels.

2. Access the battery compartment.

See WARNING “For vehicles with cargo beds...” on page 8.

3. Tilt the bed and ensure that the prop rod is properly engaged.

See WARNING “For vehicles with cargo

beds...” on page 8.

4. Lift the passenger seat.

5. Restore fuel system to operation.

See Figure 24 on page 32

.

5.1. Remove plug from fuel tank vent.

5.2. Connect vent tube to fuel tank vent.

Figure 12 Fuel Shut-off Valve – Closed Position

CLOSED (OFF) POSITION

(SELECTOR IS ALIGNED

WITH OFF MARKINGS ON THE SIDES OF VALVE)

OFF

OFF

VIEWED FROM SELECTOR

SIDE OF VALVE

«
...
22
23
24
25
26
...
»

Summary of Contents for 2005 HUV4213















































Reviews:

No comments

Related manuals for 2005 HUV4213

Brand: YTL Pages: 14

Brand: Silver Eagle Pages: 17

Brand: Suzuki Pages: 528

Brand: Applestone Pages: 134

Brand: QERIDOO Pages: 36

Brand: Baja motorsports Pages: 44

Brand: Honda Pages: 68

1985 Four Trax 250

Brand: Honda Pages: 74

WOLVERINE YXE70WPXH

Brand: Yamaha Pages: 186

Brand: Yamaha Pages: 38

Brand: MANCO Pages: 12

Brand: YX Motors Pages: 159

Brand: Dynapac Pages: 152

Brand: Sauber Pages: 11

CORRAL T-REX 2011

Brand: Peg-Perego Pages: 36

Brand: Massimo Pages: 103

Brand: Massimo Pages: 113

Brand: Massimo Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands