background image

14

SNOW THROWING TIPS

•  Always operate the snow thrower with the engine at 

full throttle. Full throttle offers the best performance.

• 

Go slower in deep, freezing or heavy wet snow. Use the 

drive speed control, NOT the throttle, to adjust speed.

•  It is easier and more efficient to remove snow im me-

 di ate ly after it falls.

• 

The best time to remove snow is the early morning. At 

this time the snow is usually dry and has not been ex-

posed to the direct sun and warming tem per a tures.

•  Slightly overlap each successive path to ensure all 

snow will be removed.

•  Throw snow downwind whenever possible.
• Ad 

just the skid plates to proper height for current snow 

con di tions.  See “TO ADJUST SKID PLATES” in this 

section of this manual.

•  For extremely heavy snow, re duce the width of snow 

removal by over lap ping previous path and moving 

slowly.

• 

Keep engine clean and clear of snow during use. This 

will help air flow and extend engine life. 

• 

After snow-throwing is completed, allow engine to run for 

a few minutes to melt snow and ice off the engine.

•  Clean the entire snow thrower thoroughly after each 

use and wipe dry so it is ready for next use.

WARNING:  Do not operate snow 

thrower if weather conditions im pair 

visibility.  Throwing snow dur ing a 

heavy, windy snowstorm can blind you 

and be hazardous to the safe operation 

of the snow thrower.

OPERATION

Summary of Contents for 11524E





























Reviews: