background image

www.spartacogroup.com 

 800-860-6170

8

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS 

COMPRESSION 

1.  Consult your connector manufacturers recommendations on using a dieless compression
 

tool with the connector and cable being used. Not all connectors are suitable for dieless tool  

 

applications.

2.  Retract the indenting nibs by pressing the release button.
3.  Position the connector, and center it between the indenting nibs. Activate the trigger and 
 

advance the nibs so the connector is held in place. Check connector for correct positioning.

4.  Insert the cable into the connector and activate the trigger until 
 

the compression is completed. A series of clicks will be heard while 

 

the compression is being made, followed by the tool running in a 

 

“free” mode. This indicates a completed cycle and a full 

 

compression.

5.  Press release button to retract the indenting nibs. and remove the 
 

connector from the tool.

TRIGGER AND RELEASE BUTTON 

1.  The ram advances when the trigger is pressed 
 

and stops when the trigger is released.

2.  To retract the ram, press the release button. The 
 

ram continues to retract while the release button is 

 

pressed.

Summary of Contents for REC-6750

















Reviews: