background image

 WARNING

Some dust created by power sanding, 

sawing, grinding, drilling, and other 

construction activities contains 

chemicals known to the State of 

California to cause cancer, birth defects 

or other reproductive harm. Some 

examples of these chemicals are:

* Lead from lead-based paints

* Crystalline silica from bricks and 

cement and other masonry products

* Arsenic and chromium from 

chemically- treated lumber.

To reduce your exposure to these 

chemicals: work in a well ventilated 

area, and work with approved safety 

equipment, such as dust masks that 

are specially designed to filter the 

microscopic particles.

 

WARNING

•  Do not use other than the 

Huskie Tools battery packs that 

are designed for use with this 

rechargeable tool.

•  Huskie Tools is not responsible for 

any damage or accident caused 

by the use of the recycled battery 

pack and the counterfeit battery 

pack.

•  Do not dispose of the battery pack 

in a fire, or expose it to excessive 

heat.

•  Do not drive the likes of nails 

into the battery pack, subject it to 

shocks, dismantle it, or attempt to 

modify it.

•  Do not allow metal objects to 

touch the battery pack terminals.

•  Do not carry or store the battery 

pack in the same container as nails 

or similar metal objects.

•  Do not charge the battery pack in a 

high-temperature location, such as 

next to a fire or in direct sunlight. 

Otherwise, the battery may 

overheat, catch fire, or explode.

•  Never use other than the dedicated 

charger to charge the battery pack. 

Otherwise, the battery may leak, 

overheat, or explode.

 

WARNING

•  After removing the battery pack 

from the tool or the charger, 

always reattach the pack cover. 

Otherwise, the battery contacts 

could be shorted, leading to a risk 

of fire.

•  When the Battery Pack Has 

Deteriorated, Replace It with a New 

One. Continued use of a damaged 

battery pack may result in heat 

generation, ignition or battery 

rupture.

III. FOR BATTERY 

CHARGER & 

BATTERY PACK

Important Safety Instructions

1) 

SAVE THESE IN STRUCTIONS 

-This manual contains important 

safety and operating instructions for 

battery charger.

2) Before using battery charger, read all 

instructions and cautionary markings 

on (1) battery charger, (2) battery 

pack.

3) 

CAUTION

 - To reduce the risk of 

injury, charge only Huskie Tools 

Battery Pack as shown in last page.

 

Other types of batteries may burst 

causing personal injury and damage.

4) Do not expose charger to rain or 

snow.

5) To reduce the risk of damaging the 

electric plug and cord, pull by plug 

rather than cord when disconnecting 

charger.

6) Make sure cord is located so that it 

will not be stepped on, tripped over, 

or otherwise subjected to damage or 

stress.

7) An extension cord should not be 

used unless absolutely necessary. 

Use of improper extension cord could 

result in a risk of fire and electric 

shock. If extension cord must be 

used, make sure:

Summary of Contents for HTP-AGR
























Reviews: