15
PowerView® LED Feedback
Blinking AQUA
Hub is booting up.
Solid AMBER
Hub is updating firmware from the Internet.
Blinking AMBER
Hub is ready to join a PowerView® Shade
Network.
Solid BLUE
Connected, normal operation.
Solid MAGENTA
Hub is ready to be connected to a WiFi Network.
Flashing BLUE
Hub is Transmitting command(s) to the
PowerView Shade Network.
Blank
Hub is not connected to power.
Solid GREEN
Hub is configured as a secondary Hub.
Solid RED
Hub does not have an IP address.
Problem: Cannot connect to the Hub with the PowerView® App.
•
Check for blinking AMBER, solid BLUE or solid MAGENTA on the front of the
Hub. (See LED Feedback chart above.)
•
Check the connection between the Hub and wireless router and that the
router is operating properly.
•
Check that the mobile device is on the same network as wireless router.
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least
20cm or more away from person’s body. RF Exposure requirements are met when installed in mobile equipment. This
module cannot be installed in portable
equipment without further testing and a change to FCC’s grant of authorization. Contact Murata regarding portable
applications.
Industry Canada
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Class B Digital Device Notice
This Class B digital apparatus complies with Canadian ICES-003, RSS-Gen and RSS-210.
CAN ICES-3 (B)/NMB-3(B)
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of
the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least
20cm or more away from person’s body.
European Conformity
We, the undersigned,
Hunter Douglas Window Fashions
One Duette Way, Broomfield, CO 80020, USA
Hunter Douglas Europe B.V.
Piekstraat 2, 3071 EL Rotterdam, The Netherlands
certify and declare under our sole responsibility that the PowerView® Hub conforms with the essential requirements of the
EMC directive 2004/108/EC and R&TTE directive 1999/5/EC.
A copy of the original declaration of conformity may be found at
www.hunterdouglas.com/RFcertifications.
