background image

STORAGE/WINTERIZATION 

                                                                                                                                   PAGE  33

engine  oil  into  the  intake  pipe  or 
manifold while engine is turning.  

DO NOT USE

 the  starter to turn  en-

gine  or  serious  engine  damage  may 
result.  
6.  Tape  the  openings  of  the  intake 
and exhaust manifolds with duct tape 
to  help  prevent  corrosion  of  the  up-
per cylinder during lay-up. 
7.  Scrape  all  rust  or  corrosion  from 
exposed metal parts and surfaces. 
Scrub  all  metal  surfaces  with  deter-
gent  and  rinse  thoroughly.  Paint  any 
bare metal. 
8.  Place  a  dust  cover  over  engine. 
Do not leave engine exposed to rain 
and sea breeze. 
9.  Disconnect  the  battery  cables; 
remove the battery from the boat. 
Clean  the  terminal  ends  and  battery 
with  a  solution  of  baking  soda  and 
water  and  rinse  thoroughly  with 
clean  water.  Apply  a  light  coat  of 
grease  on  the  terminal  end  of  the 
battery and cables. Store the battery 
in  a  cool  dry  place.  Use  a  trickle 
charger  to  keep  battery  charged.  Do 
not  charge  battery  near  any  open 
flame or in a confined area. 

CAUTION:  Wear  safety  goggles 
and  rubber  gloves  to  protect  your

 

eyes and skin. 
 
DEPARTURE FROM THE BOAT 

The  check  list for  leaving  a  boat un-
attended  is  very  important  because 
items  overlooked  often  will  not  be 
remembered  until  you  are  far  from 
the  boat  and  corrective  actions  are 
impractical or impossible.  

Primary choices for this list are items 
relating  to  the  safety  and  security  of 
the  unattended  craft:  turning  off  fuel 
valves,  properly  setting  electrical 
switches,  pumping  out  bilge  and 
leaving  the  switch  on  automatic  (or 
arrange  for  periodic  pumping  out). 

It 

is  recommended  that  the  power 
be  turned  off  when  leaving  the 
boat.

  Other  departure  checklist 

items  are  securing  ports,  windows, 
hatches and doors. 
 

ROUTINE MAINTENANCE 

Routine 

maintenance 

checklists 

should  include  items  based  on  how 
much  the  boat  is  used  (usually  in 
terms  of  engine  hours)  and  on  cal-
endar  dates  (weekly,  monthly  or 
seasonal  checks).  Typical  of  the 
former  are  oil  level  checks  and 
changes,  and  oil  and  fuel  filter 
changes. 
On  a  calendar  basis  the  lists  should 
note  such matters  as  electrolyte  lev-
els  in  storage  batteries,  pressure 
gauges  on  dry  chemical  fire  extin-
guishers,  and  all  navigation  lights. 
Check  the  operation  of  automatic 
bilge  alarms  or  pump  switches  by 
running  water  into  the  boat.  Periodi-
cally close and open 
sea  cocks  several  times  to  ensure 
their free and easy operation in case 
they  are  needed  in  an  emergency. 
Equipment  and  supplies  carried  on 
board for emergencies  should  be  in-
spected  for  any  signs  of  deteriora-
tion.

Summary of Contents for Marine Family


































































































































Reviews: