Hunter 42710-01 Installation And Operation Manual Download Page 21 | Manualshive

Page: 21 / 58

background image

21

4. Place the top of the thermostat over the two tabs on the wall

plate. Press the thermostat onto the wall plate and press to snap
the bottom tab into place.

note: Do not force the thermostat onto the wall plate, as the terminal
pins may be damaged. If the thermostat does not snap into place
properly, the unit may not work.

5. lift the front cover and insert two AA alkaline batteries.

6. restore power at the electrical panel or furnace.

InSTAllInG THE THErMOSTAT, COnT.

«
...
19
20
21
22
23
...
»

Summary of Contents for 42710-01



























































Reviews:

No comments

Related manuals for 42710-01

Brand: Hama Pages: 2

Brand: Hanna Instruments Pages: 11

Brand: White Rodgers Pages: 12

Brand: dixell Pages: 4

Brand: Tech Controllers Pages: 2

Brand: Danfoss Pages: 5

Brand: domat Pages: 8

Brand: Supco Pages: 4

Brand: KMC Controls Pages: 60

Brand: EPH Controls Pages: 2

Brand: Vicks Pages: 20

Brand: Vicks Pages: 29

Brand: McQuay Pages: 20

Brand: MCOHome Pages: 9

Brand: McKesson Pages: 4

Brand: York Survey Supply Pages: 2

Brand: SATO KEIRYOKI Pages: 12

Brand: Solfex Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands