background image

INSTALLATION 

INSIDE THE HULL INSTALLATION 

 

INSIDE THE HULL INSTALLATION

 

 

Inside the hull installation requires the mount system and control 
head be installed and operational. See Installing the Control Head 
for instruction on installing the unit. 

   

 
Inside the hull mounting generally produces good results in single 
thickness fiberglass-hulled boats. Humminbird cannot guarantee 
depth performance when transmitting and receiving through the 
hull of the boat since some signal loss occurs. The amount of loss 
depends on hull construction and thickness, and the installation. 

 

This installation requires slow-cure two-part epoxy. Do not use 
silicone or any other soft adhesive to install the transducer, as this 
material reduces the sensitivity of the unit. Five minute epoxy has 
a tendency to cure before all the air bubbles can be purged. 

 

Step One - Determine the Mounting Location 

 

Begin the transducer installation by determining where inside the 
hull to install the transducer. Consider the following to find the 
best location: 

 

• 

Observe the outside of the boat hull to find the areas that are 
mostly free from turbulent water. Avoid ribs, strakes, and other 
protrusions as these create turbulence (Figure 14). 

 

• 

As a general rule, the faster the boat can travel the further aft 
and closer to the centerline of the hull the transducer has to be 
located to remain in contact with the water at high speeds. 

 

Step Two - Test the Mounting Location 

 
There is no opportunity for adjustment after the transducer glued 
in place. Therefore, it is best to perform a trial installation on inside the hull transducers 
first, and run the boat at high speeds to determine the best mounting area. 

 

1.  At the identified mounting location, lay the transducer body face down with the 

pointed end towards the bow.

 

 
2.  Fill the hull with enough water to submerge the transducer body. Use a sand filled 

bag or other heavy object to hold the transducer in position. 

 

The transducer cannot transmit through air. The water purges any air from between 
the transducer and the hull and fills any voids in the coarse fiberglass surface. 

 

Summary of Contents for Wide Paramount

































Reviews: