Humboldt HM-5940 Product Manual Download Page 38

Page: 38 / 38

www.humboldtmfg.com

HUMBOLDT

Testing Equipment for

Construction Materials

Humboldt Mfg. Co.

875 Tollgate Road

Elgin, Illinois 60123 U.S.A.

U.S.A. Toll Free: 1.800.544.7220

Voice: 1.708.456.6300

Fax: 1.708.456.0137

Email: [email protected]

Warranty

Humboldt Mfg. Co. warrants its products to be free from defects in

material or

workmanship. The exclusive remedy for this warranty is Humboldt

Mfg. Co., factory replacement of any part or parts of such product, for

the warranty of this product please refer to Humboldt Mfg. Co. catalog

on Terms and Conditions of Sale. The purchaser is responsible for the

transportation charges. Humboldt Mfg. Co. shall not be responsible under

this warranty if the goods have been improperly maintained, installed,

operated or the goods have been altered or modified so as to adversely

affect the operation, use performance or durability or so as to change

their intended use. The Humboldt Mfg. Co. liability under the warranty

contained in this clause is limited to the repair or replacement of defective

goods and making good, defective workmanship.

Summary of Contents for HM-5940







































Search results

Summary of Contents for HM-5940

Reviews:

Related manuals for HM-5940

Brands by name

Popular brands

Humboldt HM-5940, Product Manual

Search results

Summary of Contents for HM-5940

Reviews:

Related manuals for HM-5940

Brands by name

Popular brands