manualshive.com logo in svg

Humboldt HM-5470.3F ConMatic IPC, Product Manual

Share
Download
Humboldt HM-5470.3F ConMatic IPC Product Manual Download Page 26

26

Installation and Equipment Setup
Electrical Connections

The HM-5470 is equipped with an internal digital switching power 

supply, which allows it to be used with most power configurations 

throughout the world. The unit is supplied with an IEC electrical 

cord with a standard 110V plug. 
The HM-5470 arrives ready for operation. Attach the supplied IEC 

electrical cord to the machine and plug into a standard wall recep-

tacle for use in the United States. For locations other than the U.S., 

replace the supplied electrical cord with an IEC cord that has the 

correct plug for your application. The supplied cord can also be 

used by cutting the standard plug from the cord and attaching the 

correct plug.

Power Switch

The Power Switch is located on the upper right hand corner of the 

back of the machine, above the electrical cord inlet. The Fuse  

Compartment is located between the electrical cord inlet and the 

Power Switch. The HM-5470 uses a 10 amp fuse. To begin oper-

ation, attach the supplied electrical cord, plug it in and press the 

Power Switch.

Air Connections

A constant supply of clean, dry air is required for operation. The air  

connection is located in the rear of the base cabinet, see photo below.  

The air connection is 1/4” (6mm) OD. Insert tubing (supplied) into the 

quick-connect until it bottoms out, and make sure the connections are tight. 
pressure.

Power Switch

Fuse Compartment

Summary of Contents for HM-5470.3F ConMatic IPC

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands