manualshive.com logo in svg

Humboldt HM-5470.3F ConMatic IPC, Product Manual

Share
Download
Humboldt HM-5470.3F ConMatic IPC Product Manual Download Page 19

QUICK ST

AR

T GUIDE

19

Contact Information 

Below is a view of the Contact Information screen showing 

contact information for Humboldt Support and Service. 

For quickest response go to this link on our website: 

https://www.humboldtmfg.com/support

 and fill in the 

support form.

 This will provide us with the necessary in-

formation to assist you and you will be added to the next 

position in the support cue. 

You can also email Humboldt Support at support@hum-

boldtmfg.com or Humboldt Service at service@humboldtm-

fg.com. Please include contact information and a detailed 

description of your reason for contact. 

Internet Status (4)

This indicates the status of your Internet connection,  

Connected or Disconnected.

Memory (5)

This indicates the current status of how much available  

memory is being used by the machine

Factory Screen (6)

This is for Humboldt use only.

Export Log File (7)

This button exports a log file from the machine to a USB thumb 

drive. Be sure to insert a thumb drive before exporting the file or 

you will receive an error. This file can be helpful in trouble shooting 

by Humboldt Support.

 Clicking on this panel provides contact information for  

Humboldt Support and Service

(1)

1

 Initial Set Up —Contact

Summary of Contents for HM-5470.3F ConMatic IPC

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands